HP Aruba Certified Campus Access Professional HPE7-A01 Dumps in PDF

Free HP HPE7-A01 Real Questions (page: 2)

You need to have different routing-table requirements with Aruba CX 6300 VSF configuration.
Assuming the correct layer-2 VLAN already exists, how would you create a new SVI for a separate routing table?

  1. Create a new routing table, and attach VLANs to it.
  2. Create a new VLAN, and attach the VRF to it.
  3. Create a new interface VLAN and attach vrf custom-vrf.
  4. Create a new VRF, and add new SVI under the configuration.

Answer(s): D

Explanation:

In Aruba CX switches, to have separate routing tables (VRFs), you must first create a new VRF and then create an SVI (interface VLAN) within that VRF’s configuration. This allows the SVI to use the specific routing table associated with the VRF.



Your customer has asked you to assign a switch management role for a new user. The customer requires the user role to view nonsensitive switch configuration information and only has the GET method for REST API for all resources other than \login and \logout.
Which default AOS-CX user role meets these requirements?

  1. sysadmin
  2. config
  3. administrators
  4. operators

Answer(s): D

Explanation:

The default operators role in Aruba AOS-CX provides read-only access to the switch configuration and allows only GET requests (except for login/logout). This matches the requirement for viewing nonsensitive configuration information without the ability to make changes.



You are deploying a bonded 40 MHz wide channel.
What is the difference in the noise floor perceived by a client using this bonded channel as compared to an unbonded 20MHz wide channel?

  1. 6dB
  2. 8dB
  3. 3dB
  4. 4dB

Answer(s): C

Explanation:

When doubling the channel width from 20 MHz to 40 MHz, the noise floor increases by 3dB because the client receives twice as much noise power across the wider frequency band.



AppRF 2.0 allows you to:

  1. monitor applications and radio frequencies
  2. customize application signatures
  3. configure ACL and bandwidth control for applications
  4. classify web content based on reputation

Answer(s): C

Explanation:

AppRF 2.0 in Aruba solutions enables administrators to apply access control lists (ACLs) and bandwidth policies to specific applications, improving application visibility and control at the network edge.



A system engineer needs to preconfigure several CX 6300 switches that will be sent to a remote office. An untrained local field technician will do the rollout of the switches and the mounting of several AP-515s and AP-575s. Cables running to the APs are not labeled.
The VLANs are already preconfigured to VLAN 100 (mgmt.), VLAN 200 (clients), and VLAN 300 (guests).
What is the correct configuration to ensure that APs will work properly?





Answer(s): C

Explanation:

The configuration correctly matches the AP models (AP-515 and AP-575) using sys-desc AP-515 and sys-desc AP-575 in the LLDP group, ensuring automatic profile assignment for both AP models. It also associates the correct role and LLDP group, sets the appropriate VLAN trunking, and does not include unnecessary or misplaced commands. This ensures the APs will receive the right port configuration regardless of where they are connected.



You are setting up a customer’s 150 headless IoT devices that do not support 802.1X.
What should you use?

  1. Multiple Pre-Shared Keys (MPSK) Local
  2. HPE Aruba Networking ClearPass profiling with WPA-PSK
  3. HPE Aruba Networking ClearPass profiling with MAC-AUTH
  4. Multiple Pre-Shared Keys (MPSK) with WPA3-AES

Answer(s): A

Explanation:

MPSK Local enables you to assign unique pre-shared keys to each IoT device without requiring 802.1X support, increasing security and simplifying onboarding for large deployments of headless devices.



How is Dynamic Multicast Optimization (DMO) implemented in an HPE Aruba Networking wireless network?

  1. DMO is configured individually for each VLAN in use in the network.
  2. The controller uses QoS to provide equal air time for multicast traffic.
  3. The controller converts multicast streams into unicast streams.
  4. The wireless AP converts multicast streams into unicast streams.

Answer(s): C



You are proposing new CX 8360 VSX switches to replace a customer’s existing core switches. The customer is concerned about the possibility of a split-brain scenario between the VSX pair.
How is the VSX pair affected when the ISL is down and keepalive is up?

  1. The VSX pair is out-of-sync.
  2. The VSX pair nodes are still forwarding traffic.
  3. The VSX pair is not at risk.
  4. The VSX LAGs are in a degraded state.

Answer(s): B

Explanation:

When the Inter-Switch Link (ISL) is down but the keepalive link is still operational, both VSX switches detect each other as active and continue to forward traffic independently. This prevents a split-brain scenario because the keepalive link ensures both nodes are aware of each other’s status.



Share your comments for HP HPE7-A01 exam with other users:

B
Bsmaind
8/20/2023 9:22:00 AM

hello nice dumps

B
beau
1/12/2024 4:53:00 PM

good resource for learning

S
Sandeep
12/29/2023 4:07:00 AM

very useful

K
kevin
9/29/2023 8:04:00 AM

physical tempering techniques

B
Blessious Phiri
8/15/2023 4:08:00 PM

its giving best technical knowledge

T
Testbear
6/13/2023 11:15:00 AM

please upload

S
shime
10/24/2023 4:23:00 AM

great question with explanation thanks!!

T
Thembelani
5/30/2023 2:40:00 AM

does this exam have lab sections?

S
Shin
9/8/2023 5:31:00 AM

please upload

P
priti kagwade
7/22/2023 5:17:00 AM

please upload the braindump for .net

R
Robe
9/27/2023 8:15:00 PM

i need this exam 1z0-1107-2. please.

C
Chiranthaka
9/20/2023 11:22:00 AM

very useful!

N
Not Miguel
11/26/2023 9:43:00 PM

for this question - "which three type of basic patient or member information is displayed on the patient info component? (choose three.)", list of conditions is not displayed (it is displayed in patient card, not patient info). so should be thumbnail of chatter photo

A
Andrus
12/17/2023 12:09:00 PM

q52 should be d. vm storage controller bandwidth represents the amount of data (in terms of bandwidth) that a vms storage controller is using to read and write data to the storage fabric.

R
Raj
5/25/2023 8:43:00 AM

nice questions

M
max
12/22/2023 3:45:00 PM

very useful

M
Muhammad Rawish Siddiqui
12/8/2023 6:12:00 PM

question # 208: failure logs is not an example of operational metadata.

S
Sachin Bedi
1/5/2024 4:47:00 AM

good questions

K
Kenneth
12/8/2023 7:34:00 AM

thank you for the test materials!

H
Harjinder Singh
8/9/2023 4:16:00 AM

its very helpful

S
SD
7/13/2023 12:56:00 AM

good questions

K
kanjoe
7/2/2023 11:40:00 AM

good questons

M
Mahmoud
7/6/2023 4:24:00 AM

i need the dumb of the hcip security v4.0 exam

W
Wei
8/3/2023 4:18:00 AM

upload the dump please

S
Stephen
10/3/2023 6:24:00 PM

yes, iam looking this

S
Stephen
8/4/2023 9:08:00 PM

please upload cima e2 managing performance dumps

H
hp
6/16/2023 12:44:00 AM

wonderful questions

P
Priyo
11/14/2023 2:23:00 AM

i used this site since 2000, still great to support my career

J
Jude
8/29/2023 1:56:00 PM

why is the answer to "which of the following is required by scrum?" all of the following stated below since most of them are not mandatory? sprint retrospective. members must be stand up at the daily scrum. sprint burndown chart. release planning.

M
Marc blue
9/15/2023 4:11:00 AM

great job. hope this helps out.

A
Anne
9/13/2023 2:33:00 AM

upload please. many thanks!

P
pepe el toro
9/12/2023 7:55:00 PM

this is so interesting

A
Antony
11/28/2023 12:13:00 AM

great material thanks

T
Thembelani
5/30/2023 2:22:00 AM

anyone who wrote this exam recently

AI Tutor 👋 I’m here to help!