An administrator wants to check the performance metrics for the workloads and their virtual disks that are running on a vSAN cluster, but no statistical charts are displayed in the vSphere client.Why is this behavior being seen? Options:
Answer(s): C
Some tools allow for measuring latency peaks. This unfortunately isn't ideal, as it can unfairly represent statistical outliers, which may very well occur when there is little to no I/O activity. The best way to understand the actual behavior of VM and application latencies is to observe in time based performance graphs. Depending on the level of detail, you may need to measure at the individual VMDK level. Become familiar with these graphs to determine what is normal, and what is not for that given application. This is where you can use built-in functionality of vCenter and the vSAN performance service metrics to gather this information.
https://core.vmware.com/resource/troubleshooting-vsan-performance#_Toc536646873
In a vSAN stretched cluster, which value must be set in the vSAN policy if there is no requirement for data mirroring across sites?Options:
Answer(s): A
https://www.delltechnologies.com/asset/en-us/products/converged-infrastructure/technical-support/h15275-vxrail-planning-guide-virtual-san-stretched-cluster.pdf (5)
After a vSAN Witness Appliance network configuration, the vSAN administrator notices that vSAN traffic flows from vmk0 (Management Traffic) rather than vmk1 (vSAN Traffic).Which step should be taken to resolve this issue? Options:
Click on next and assign the IP address for the Witnesspg vmkernel interface. The vmk1 interface cannot be configured with an IP address on the same range as that of vmk0. This is because Management traffic and vSAN traffic use the default TCP/IP stack. If both vmk0 and vmk1 are configured on the same range, a multihoming condition will occur and vSAN traffic will flow from vmk0, rather than vmk1.
http://www.vmwarearena.com/vsan-stretched-cluster-how-to-configure-vsan-witness-appliance/
During a maintenance action on a vSAN node, a vSAN administrator noticed that the default repair delay time is about to be reached.Which two commands must be run to extend the time? (Choose two.) Options:
Answer(s): C,D
https://kb.vmware.com/s/article/2075456
A company has engaged a consultant to upgrade an existing vSAN cluster to vSAN 7.0 U1. During the discovery phase, the consultant found the following information about the existing environment: * The VMware vCenter Server has recently been upgraded from VMware vSphere 6.7 U3 to version 7.0 U1.* The vSAN Cluster was recently expanded with identical hardware specification, but from a different hardware vendor.* The hardware for each vSAN node is listed on the vSAN Compatibility Guide (VCG) for vSAN 7.* The vSAN Cluster has the following configuration:- vSAN version: 6.6.1- Number of vSAN nodes: 10- Encryption: enabled- Deduplication and Compression: enabled- vSAN Capacity Utilization: 60%* Each vSAN node has the following configuration:- VMware vSphere ESXi version: 6.5 Update 3- CPU: 2 processors, 20 cores- RAM: 768GB RAM.- Disk: 2 Cache SSDs and 6 Capacity SSDs- Network: 4 x 10GbEWhich three recommendations should the consultant make to ensure all data remains protected in the event of a vSAN failure? (Choose three.)Options:
Answer(s): B,D,E
Share your comments for VMware 5V0-21.21 exam with other users:
question 75: option c is correct answer
please add this exam
please upoad
has anyone recently attended safe 6.0 certification? is it the samq question from here.
expository experience
52 should be b&c. controller failure has nothing to do with this type of issue. degraded state tells us its a raid issue, and if the os is missing then the bootable device isnt found. the only other consideration could be data loss but thats somewhat broad whereas b&c show understanding of the specific issues the question is asking about.
great help!!!
very useful tools
looks a good platform to prepare az-104
want to pass the exam
good resource
question 11 : d
only the free dumps will be enough for pass, or have to purchase the premium one. please suggest.
good questions. thanks.
good for practice.
great case study
the questions in this exam dumps is valid. i passed my test last monday. i only whish they had their pricing in inr instead of usd. but it is still worth it.
q40 the answer is not d, why are you giving incorrect answers? snapshot consolidation is used to merge the snapshot delta disk files to the vm base disk
thanks, very relevant
wrong answer. it is true not false.
please i need the mo-100 questions
very good use full
very valid questions
will these question help me to clear pl-300 exam?
please provide me with these dumps questions. thanks
in the pdf downloaded is write google cloud database engineer i think that it isnt the correct exam
i think you have the answers wrong regarding question: "what are three core principles of web content accessibility guidelines (wcag)? answer: robust, operable, understandable
these questions are not valid , they dont come for the exam now
question looks valid
good for practice
need more q&a to go ahead
question 59 - a newly-created role is not assigned to any user, nor granted to any other role. answer is b https://docs.snowflake.com/en/user-guide/security-access-control-overview
just passed my exam today. i saw all of these questions in my text today. so i can confirm this is a valid dump.
needed dumps
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your 5V0-21.21, please sign in or create a free account.