An administrator wants to check the performance metrics for the workloads and their virtual disks that are running on a vSAN cluster, but no statistical charts are displayed in the vSphere client.Why is this behavior being seen? Options:
Answer(s): C
Some tools allow for measuring latency peaks. This unfortunately isn't ideal, as it can unfairly represent statistical outliers, which may very well occur when there is little to no I/O activity. The best way to understand the actual behavior of VM and application latencies is to observe in time based performance graphs. Depending on the level of detail, you may need to measure at the individual VMDK level. Become familiar with these graphs to determine what is normal, and what is not for that given application. This is where you can use built-in functionality of vCenter and the vSAN performance service metrics to gather this information.
https://core.vmware.com/resource/troubleshooting-vsan-performance#_Toc536646873
In a vSAN stretched cluster, which value must be set in the vSAN policy if there is no requirement for data mirroring across sites?Options:
Answer(s): A
https://www.delltechnologies.com/asset/en-us/products/converged-infrastructure/technical-support/h15275-vxrail-planning-guide-virtual-san-stretched-cluster.pdf (5)
After a vSAN Witness Appliance network configuration, the vSAN administrator notices that vSAN traffic flows from vmk0 (Management Traffic) rather than vmk1 (vSAN Traffic).Which step should be taken to resolve this issue? Options:
Click on next and assign the IP address for the Witnesspg vmkernel interface. The vmk1 interface cannot be configured with an IP address on the same range as that of vmk0. This is because Management traffic and vSAN traffic use the default TCP/IP stack. If both vmk0 and vmk1 are configured on the same range, a multihoming condition will occur and vSAN traffic will flow from vmk0, rather than vmk1.
http://www.vmwarearena.com/vsan-stretched-cluster-how-to-configure-vsan-witness-appliance/
During a maintenance action on a vSAN node, a vSAN administrator noticed that the default repair delay time is about to be reached.Which two commands must be run to extend the time? (Choose two.) Options:
Answer(s): C,D
https://kb.vmware.com/s/article/2075456
A company has engaged a consultant to upgrade an existing vSAN cluster to vSAN 7.0 U1. During the discovery phase, the consultant found the following information about the existing environment: * The VMware vCenter Server has recently been upgraded from VMware vSphere 6.7 U3 to version 7.0 U1.* The vSAN Cluster was recently expanded with identical hardware specification, but from a different hardware vendor.* The hardware for each vSAN node is listed on the vSAN Compatibility Guide (VCG) for vSAN 7.* The vSAN Cluster has the following configuration:- vSAN version: 6.6.1- Number of vSAN nodes: 10- Encryption: enabled- Deduplication and Compression: enabled- vSAN Capacity Utilization: 60%* Each vSAN node has the following configuration:- VMware vSphere ESXi version: 6.5 Update 3- CPU: 2 processors, 20 cores- RAM: 768GB RAM.- Disk: 2 Cache SSDs and 6 Capacity SSDs- Network: 4 x 10GbEWhich three recommendations should the consultant make to ensure all data remains protected in the event of a vSAN failure? (Choose three.)Options:
Answer(s): B,D,E
Share your comments for VMware 5V0-21.21 exam with other users:
is it legit questions from sap certifications ?
question 16 should be b (changing the connector settings on the monitor) pc and monitor were powered on. the lights on the pc are on indicating power. the monitor is showing an error text indicating that it is receiving power too. this is a clear sign of having the wrong input selected on the monitor. thus, the "connector setting" needs to be switched from hdmi to display port on the monitor so it receives the signal from the pc, or the other way around (display port to hdmi).
q 10. ans is d (in the target org: open deployment settings, click edit next to the source org. select allow inbound changes and save
very useful
i purchased this exam dumps from another website with way more questions but they were all invalid and outdate. this exam dumps was right to the point and all from recent exam. it was a hard pass.
it was a good experience and i got 90% in the 200-901 exam.
hi please upload this
please upload it
really need this dump. can you please help.
really good and covers many areas explaining the answer.
yes, can you please upload the exam?
how many questions are there in these dumps?
hi team, please upload this , i need it.
question 14 - run terraform import: this is the recommended best practice for bringing manually created or destroyed resources under terraform management. you use terraform import to associate an existing resource with a terraform resource configuration. this ensures that terraform is aware of the resource, and you can subsequently manage it with terraform.
please upload dump. thanks in advance.
great great
answer 16 should be b your organizational policies require you to use virtual machines directly
the question are kind of tricky of you didnt get the hnag on it.
can anyone tell me if this is for rhel8 or rhel9?
good content
pdb and cdb are critical to the database
till 104 questions are free, lets see how it helps me in my exam today.
question # 56, answer is true not false.
i would be requiring dumps to prepare for certification exam
very helpful
control file is the heart of rman backup
hi could you please upload the ibm c2090-543 dumps
appriciate if you could upload this again
please upload the dump
i found some questions answers mismatch with explanation answers. please properly update
nothing to mention
knowable questions
very helpfull
good questions
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your 5V0-21.21, please sign in or create a free account.