The display sync-configuration compare command is executed on the backup WAC in HSB to check wireless configuration synchronization. Based on the command output, which of the following statements are true? (Select All that apply)
Answer(s): A,C
The display sync-configuration compare command is used to check whether the public configurations on two WACs are consistent after wireless configuration synchronization. The command output shows the differences between the configurations on the master and backup WACs. In this case, the configuration of vap-profile name 3 exists on the master WAC but not on the backup WAC.
https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/display- sync-configuration-compare
In a dual-link backup scenario, the active/standby link switchover mode is set to priority. When the active link recovers, the AP detects that the original active link has a higher priority and triggers a switchback. How many Echo intervals does the AP wait for before switching back to the original primary WAC?
Answer(s): C
In a dual-link backup scenario, when the active link recovers, the AP waits for 15 Echo intervals before switching back to the original primary WAC. This prevents frequent link switchovers caused by unstable links.
https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/dual-link- backup
In a dual-link HSB scenario, after an AP sets up CAPWAP links with the active and standby WACs, which of the following types of packets does the AP periodically send to the WACs to detect link status?
In a dual-link HSB scenario, after an AP sets up CAPWAP links with the active and standby WACs, the AP periodically sends Echo packets to the WACs to detect link status. The Echo packets are sent every 30 seconds by default.
https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/dual-link- hsb
Which of the followings is not a roaming optimization solution?
Answer(s): B
Smart roaming is not a roaming optimization solution, but a feature that allows an AP to automatically adjust its transmit power based on signal strength and interference level. The other options are all roaming optimization solutions that can reduce roaming latency and packet loss.
https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/smart- roaming
DRAG DROP (Drag and Drop is not supported)802. 11r fast roaming (over-the-air) is enabled on the WLAN shown in the figure. A STA roams from AP1 to AP2. Sort the steps in chronological order during the 802.11r fast roaming process between WACs.
Answer(s): A
According to the Huawei documents and resources, the chronological order during the 802.11r fast roaming process between WACs is as follows:2.The STA accesses the network through API. This is the initial association process before roaming. 1.The STA initiates an 802.11 FT authentication request to AP2. This is the first step of the roaming process when the STA moves to a new AP.3.AP2 starts the reassociation timer, and sends an 802.11 FT authentication response to the ST A. This is the second step of the roaming process when AP2 responds to the STA's request and sets a timer for reassociation.4.The STA generates and installs a P TK based on the information contained in the response frame. This is the third step of the roaming process when the STA derives a new pairwise key for encryption. 5.The STA sends a reassociation request to AP2. This is the fourth step of the roaming process when the STA requests to reassociate with AP2.6.AP2 generates and installs a PTK according to PMK-RI and information contained in the request frame. This is the fifth step of the roaming process when AP2 derives the same pairwise key as the STA.7.After receiving the reassociation request, AP2 disables the reassociation timer, and then sends a reassociation reg onse to the STA. This is the sixth step of the roaming process when AP2 confirms the reassociation with the STA and stops the timer.8.The STA receives the response frame of AP2. The roaming process is complete. This is the final step of the roaming process when the STA completes the handover to AP2. Therefore, 2, 1, 3, 4, 5, 6, 7, 8 is the correct answer.
https://support.huawei.com/enterprise/en/doc/EDOC1100169459/8d79210e/configuring-wireless- mesh-networking
Share your comments for Huawei H12-351_V1.0 exam with other users:
how i can see exam questions?
can you please upload please?
question 75: option c is correct answer
please add this exam
please upoad
has anyone recently attended safe 6.0 certification? is it the samq question from here.
expository experience
52 should be b&c. controller failure has nothing to do with this type of issue. degraded state tells us its a raid issue, and if the os is missing then the bootable device isnt found. the only other consideration could be data loss but thats somewhat broad whereas b&c show understanding of the specific issues the question is asking about.
great help!!!
very useful tools
looks a good platform to prepare az-104
want to pass the exam
good resource
question 11 : d
only the free dumps will be enough for pass, or have to purchase the premium one. please suggest.
good questions. thanks.
good for practice.
great case study
the questions in this exam dumps is valid. i passed my test last monday. i only whish they had their pricing in inr instead of usd. but it is still worth it.
q40 the answer is not d, why are you giving incorrect answers? snapshot consolidation is used to merge the snapshot delta disk files to the vm base disk
thanks, very relevant
wrong answer. it is true not false.
please i need the mo-100 questions
very good use full
very valid questions
will these question help me to clear pl-300 exam?
please provide me with these dumps questions. thanks
in the pdf downloaded is write google cloud database engineer i think that it isnt the correct exam
i think you have the answers wrong regarding question: "what are three core principles of web content accessibility guidelines (wcag)? answer: robust, operable, understandable
these questions are not valid , they dont come for the exam now
question looks valid
good for practice
need more q&a to go ahead
question 59 - a newly-created role is not assigned to any user, nor granted to any other role. answer is b https://docs.snowflake.com/en/user-guide/security-access-control-overview
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your H12-351_V1.0, please sign in or create a free account.