The display sync-configuration compare command is executed on the backup WAC in HSB to check wireless configuration synchronization. Based on the command output, which of the following statements are true? (Select All that apply)
Answer(s): A,C
The display sync-configuration compare command is used to check whether the public configurations on two WACs are consistent after wireless configuration synchronization. The command output shows the differences between the configurations on the master and backup WACs. In this case, the configuration of vap-profile name 3 exists on the master WAC but not on the backup WAC.
https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/display- sync-configuration-compare
In a dual-link backup scenario, the active/standby link switchover mode is set to priority. When the active link recovers, the AP detects that the original active link has a higher priority and triggers a switchback. How many Echo intervals does the AP wait for before switching back to the original primary WAC?
Answer(s): C
In a dual-link backup scenario, when the active link recovers, the AP waits for 15 Echo intervals before switching back to the original primary WAC. This prevents frequent link switchovers caused by unstable links.
https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/dual-link- backup
In a dual-link HSB scenario, after an AP sets up CAPWAP links with the active and standby WACs, which of the following types of packets does the AP periodically send to the WACs to detect link status?
In a dual-link HSB scenario, after an AP sets up CAPWAP links with the active and standby WACs, the AP periodically sends Echo packets to the WACs to detect link status. The Echo packets are sent every 30 seconds by default.
https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/dual-link- hsb
Which of the followings is not a roaming optimization solution?
Answer(s): B
Smart roaming is not a roaming optimization solution, but a feature that allows an AP to automatically adjust its transmit power based on signal strength and interference level. The other options are all roaming optimization solutions that can reduce roaming latency and packet loss.
https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/smart- roaming
DRAG DROP (Drag and Drop is not supported)802. 11r fast roaming (over-the-air) is enabled on the WLAN shown in the figure. A STA roams from AP1 to AP2. Sort the steps in chronological order during the 802.11r fast roaming process between WACs.
Answer(s): A
According to the Huawei documents and resources, the chronological order during the 802.11r fast roaming process between WACs is as follows:2.The STA accesses the network through API. This is the initial association process before roaming. 1.The STA initiates an 802.11 FT authentication request to AP2. This is the first step of the roaming process when the STA moves to a new AP.3.AP2 starts the reassociation timer, and sends an 802.11 FT authentication response to the ST A. This is the second step of the roaming process when AP2 responds to the STA's request and sets a timer for reassociation.4.The STA generates and installs a P TK based on the information contained in the response frame. This is the third step of the roaming process when the STA derives a new pairwise key for encryption. 5.The STA sends a reassociation request to AP2. This is the fourth step of the roaming process when the STA requests to reassociate with AP2.6.AP2 generates and installs a PTK according to PMK-RI and information contained in the request frame. This is the fifth step of the roaming process when AP2 derives the same pairwise key as the STA.7.After receiving the reassociation request, AP2 disables the reassociation timer, and then sends a reassociation reg onse to the STA. This is the sixth step of the roaming process when AP2 confirms the reassociation with the STA and stops the timer.8.The STA receives the response frame of AP2. The roaming process is complete. This is the final step of the roaming process when the STA completes the handover to AP2. Therefore, 2, 1, 3, 4, 5, 6, 7, 8 is the correct answer.
https://support.huawei.com/enterprise/en/doc/EDOC1100169459/8d79210e/configuring-wireless- mesh-networking
Share your comments for Huawei H12-351_V1.0 exam with other users:
great case study
the questions in this exam dumps is valid. i passed my test last monday. i only whish they had their pricing in inr instead of usd. but it is still worth it.
q40 the answer is not d, why are you giving incorrect answers? snapshot consolidation is used to merge the snapshot delta disk files to the vm base disk
thanks, very relevant
wrong answer. it is true not false.
please i need the mo-100 questions
very good use full
very valid questions
will these question help me to clear pl-300 exam?
please provide me with these dumps questions. thanks
in the pdf downloaded is write google cloud database engineer i think that it isnt the correct exam
i think you have the answers wrong regarding question: "what are three core principles of web content accessibility guidelines (wcag)? answer: robust, operable, understandable
these questions are not valid , they dont come for the exam now
question looks valid
good for practice
need more q&a to go ahead
question 59 - a newly-created role is not assigned to any user, nor granted to any other role. answer is b https://docs.snowflake.com/en/user-guide/security-access-control-overview
just passed my exam today. i saw all of these questions in my text today. so i can confirm this is a valid dump.
needed dumps
very helpful
will post once the exam is finished
relevant questions
just clear exam on 10/06/2202 dumps is valid all questions are came same in dumps only 2 new questions total 46 questions 1 case study with 5 question no lab/simulation in my exam please check the answers best of luck
q.112 - correct answer is c - the event registry is a module that provides event definitions. answer a - not correct as it is the definition of event log
good and useful.
good questions
good content
totally not correct answers. 21. you have one gcp account running in your default region and zone and another account running in a non-default region and zone. you want to start a new compute engine instance in these two google cloud platform accounts using the command line interface. what should you do? correct: create two configurations using gcloud config configurations create [name]. run gcloud config configurations activate [name] to switch between accounts when running the commands to start the compute engine instances.
kindly upload the dumps
still learning
excellent way to learn
help so much
understand sql col.
i would give 5 stars to this website as i studied for az-800 exam from here. it has all the relevant material available for preparation. i got 890/1000 on the test.
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your H12-351_V1.0, please sign in or create a free account.