The display sync-configuration compare command is executed on the backup WAC in HSB to check wireless configuration synchronization. Based on the command output, which of the following statements are true? (Select All that apply)
Answer(s): A,C
The display sync-configuration compare command is used to check whether the public configurations on two WACs are consistent after wireless configuration synchronization. The command output shows the differences between the configurations on the master and backup WACs. In this case, the configuration of vap-profile name 3 exists on the master WAC but not on the backup WAC.
https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/display- sync-configuration-compare
In a dual-link backup scenario, the active/standby link switchover mode is set to priority. When the active link recovers, the AP detects that the original active link has a higher priority and triggers a switchback. How many Echo intervals does the AP wait for before switching back to the original primary WAC?
Answer(s): C
In a dual-link backup scenario, when the active link recovers, the AP waits for 15 Echo intervals before switching back to the original primary WAC. This prevents frequent link switchovers caused by unstable links.
https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/dual-link- backup
In a dual-link HSB scenario, after an AP sets up CAPWAP links with the active and standby WACs, which of the following types of packets does the AP periodically send to the WACs to detect link status?
In a dual-link HSB scenario, after an AP sets up CAPWAP links with the active and standby WACs, the AP periodically sends Echo packets to the WACs to detect link status. The Echo packets are sent every 30 seconds by default.
https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/dual-link- hsb
Which of the followings is not a roaming optimization solution?
Answer(s): B
Smart roaming is not a roaming optimization solution, but a feature that allows an AP to automatically adjust its transmit power based on signal strength and interference level. The other options are all roaming optimization solutions that can reduce roaming latency and packet loss.
https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/smart- roaming
DRAG DROP (Drag and Drop is not supported)802. 11r fast roaming (over-the-air) is enabled on the WLAN shown in the figure. A STA roams from AP1 to AP2. Sort the steps in chronological order during the 802.11r fast roaming process between WACs.
Answer(s): A
According to the Huawei documents and resources, the chronological order during the 802.11r fast roaming process between WACs is as follows:2.The STA accesses the network through API. This is the initial association process before roaming. 1.The STA initiates an 802.11 FT authentication request to AP2. This is the first step of the roaming process when the STA moves to a new AP.3.AP2 starts the reassociation timer, and sends an 802.11 FT authentication response to the ST A. This is the second step of the roaming process when AP2 responds to the STA's request and sets a timer for reassociation.4.The STA generates and installs a P TK based on the information contained in the response frame. This is the third step of the roaming process when the STA derives a new pairwise key for encryption. 5.The STA sends a reassociation request to AP2. This is the fourth step of the roaming process when the STA requests to reassociate with AP2.6.AP2 generates and installs a PTK according to PMK-RI and information contained in the request frame. This is the fifth step of the roaming process when AP2 derives the same pairwise key as the STA.7.After receiving the reassociation request, AP2 disables the reassociation timer, and then sends a reassociation reg onse to the STA. This is the sixth step of the roaming process when AP2 confirms the reassociation with the STA and stops the timer.8.The STA receives the response frame of AP2. The roaming process is complete. This is the final step of the roaming process when the STA completes the handover to AP2. Therefore, 2, 1, 3, 4, 5, 6, 7, 8 is the correct answer.
https://support.huawei.com/enterprise/en/doc/EDOC1100169459/8d79210e/configuring-wireless- mesh-networking
Share your comments for Huawei H12-351_V1.0 exam with other users:
can i have the icdl excel exam
please upload it
hye when will post again the past year question for this h13-311_v3 part since i have to for my test tommorow…thank you very much
on question 22, option b-once per session is also valid.
this website is very helpful
its my first time exam
correct answers are device configuration-enable the automatic installation of webview2 runtime. & policy management- prevent users from submitting feedback.
is this dump still valid? today is 9-july-2023
i need this exam.. please upload these are really helpful
please upload the oracle 1z0-1059-22 dumps
very good questions
nice, first step to exams
is this valid for chfiv9 as well... as i am reker 3rd time...
great exam for people taking 220-1101
this is very helpfull for me
just started preparing for the exam
these are the type of questions i need.
does this actually work? are they the exam questions and answers word for word?
thanks for providing these questions
interesting
these dumps are pretty good.
good questions
dbua is used for upgrading oracle database
i am thrilled to say that i passed my amazon web services mls-c01 exam, thanks to study materials. they were comprehensive and well-structured, making my preparation efficient.
please upload latest ibm ace c1000-056 dumps
if only explanations were provided...
yes .. i need the dump if you can help me
good morning, could you please upload this exam again?
hi please upload sre foundation and practitioner exam questions
the exam is listed as 80 questions with a pass mark of 70%, how is your 50 questions related?
all questions are so important and covers all ccna modules
q 44. ans:- b (goto setup > order settings > select enable optional price books for orders) reference link --> https://resources.docs.salesforce.com/latest/latest/en-us/sfdc/pdf/sfom_impl_b2b_b2b2c.pdf(decide whether you want to enable the optional price books feature. if so, select enable optional price books for orders. you can use orders in salesforce while managing price books in an external platform. if you’re using d2c commerce, you must select enable optional price books for orders.)
"cost of replacing data if it were lost" is also correct.
pls upload the questions
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your H12-351_V1.0, please sign in or create a free account.