HP Aruba Certified Campus Access Professional HPE7-A01 Dumps in PDF

Free HP HPE7-A01 Real Questions (page: 19)

When setting up an AOS-CX VSX pair, which information does the Inter-Switch Protocol synchronize in the configuration created?

  1. RPVST+
  2. SVI
  3. UDLD
  4. MSTP

Answer(s): D



What is enabled by LLDP-MED?

  1. Voice VLANs can be automatically configured for VoIP phones.
  2. GVRP VLAN information can be used to dynamically add VLANs to a trunk.
  3. iSCSI client devices can set the required MTU setting for the port.
  4. iSCSI client devices can request to have flow control enabled.

Answer(s): A

Explanation:

LLDP-MED (Link Layer Discovery Protocol – Media Endpoint Discovery) allows switches to automatically assign and configure the correct Voice VLAN to VoIP phones, enabling seamless voice network deployments.



Refer to the output from a CX6100 switch:

What is the correct detail that can be observed from the output above?

  1. The dBm values for Tx are too far away from 0, and the link is down.
  2. the dBm values for Rx are within acceptable values, and the link is up.
  3. The dBm values for Rx are too low, indicating that the link is down.
  4. The dBm values for Tx are too high and affect Rx signals.

Answer(s): C

Explanation:

The Rx Power is shown as -40.00 dBm (0.0001 mW), which is extremely low and far below operational thresholds. Additionally, alarms indicate "Rx Power low alarm," "Rx Power low warning," and "Rx loss of signal," confirming that the link is down due to insufficient received signal strength.



What is true regarding 802.11k?

  1. It extends radio measurements to define mechanisms for wireless network management of stations.
  2. It reduces roaming delay by pre-authenticating clients with multiple target APs before a client roams to an
    AP.
  3. It provides mechanisms for APs and clients to dynamically measure the available radio resources.
    -D. It considers several metrics before it determines if a client should be steered to the 5GHz band, including client RSSI.
    -

Answer(s): C



In a CX 8325, how do you configure the IP address 10.10.10.1 for the interface in default state for interface SVI 100 access and port 1/1/1?

  1. int vlan 100, ip address 10.10.10.1/24, int 1/1/1, switching, vlan access 100
  2. int vlan 100, ip address 10.10.10.1/24, int 1/1/1 vlan access 100
  3. int vlan 100, ip address 10.10.10.1/24, int 1/1/1, trunking, valn native 100
  4. int vlan, ip address 10.10.10.1/24, int 1/1/1, no routing, vlan access 100

Answer(s): B

Explanation:

To configure an SVI with IP address 10.10.10.1 on VLAN 100 and assign port 1/1/1 as an access port in VLAN 100 on the CX 8325, you configure the VLAN interface with the IP address and set the port as an access port for that VLAN. This enables both routing and switching for hosts connected to port 1/1/1 on VLAN 100.



Your customer currently has two (2) 5406 modular switches with MSTP configured as their core switches. You are proposing a new solution.
What would you explain regarding the AOS-CX VSX switch pair when the Spanning-tree needs to be set up?

  1. Enable vsx-peer stp-global in vsx mode to sync the configuration.
  2. Spanning-tree configuration is synced by default with VSX.
  3. Use vsx-sync in the MSTP region configuration to get synced.
  4. Enable vsx-sync stp-global in vsx mode to sync the configuration.

Answer(s): D

Explanation:

In AOS-CX VSX, to synchronize spanning-tree configuration (such as MSTP) between the VSX pair, you must enable vsx-sync stp-global in VSX mode. This ensures both switches have consistent spanning-tree settings, unlike classic modular switches where spanning-tree configuration is manually matched.



A customer has several hundred wireless IoT devices and is looking for an authentication solution that meets the following requirements:
-The wireless traffic between the IoT devices and the Access Point must be encrypted -Unique passphrase per device -Use fingerprint information to perform role-based access
Which solution will address the customer’s requirements? (Choose two.)

  1. MPSK and an internal RADIUS server
  2. MPSK Local with MAC Authentication
  3. Local User Derivation Rules
  4. HPE Aruba Networking ClearPass Policy Manager
  5. MPSK Local with EAP-TLS

Answer(s): A,D

Explanation:

MPSK (Multi Pre-Shared Key) provides unique passphrases per device, ensuring each IoT device has an individual key and encrypted wireless communication.
ClearPass Policy Manager enables advanced authentication (including fingerprinting), dynamic role-based access, and integrates with MPSK or RADIUS for per-device policies. Together, they meet all listed requirements: encryption, unique credentials, and fingerprint-based access control.



A large retail client is looking to generate a rich set of contextual data based on the location information of wireless clients in their stores.
Which standard uses Round Trip Time (RTT) and Fine Time Measurements (FTM) to calculate the distance a client is from an AP?

  1. 802.11mc
  2. 802.11be
  3. 802.11v
  4. 802.11ah

Answer(s): A

Explanation:

802.11mc introduces Fine Timing Measurement (FTM), which uses Round Trip Time (RTT) calculations between the client and the AP to accurately determine the client’s distance from the access point, enabling precise location-based services and contextual data collection.



Share your comments for HP HPE7-A01 exam with other users:

N
Nitin Mindhe
11/27/2023 6:12:00 AM

great !! it is really good

B
BailleyOne
11/22/2023 1:45:00 AM

explanations for the answers are to the point.

P
patel
10/25/2023 8:17:00 AM

how can rea next

M
MortonG
10/19/2023 6:32:00 PM

question: 128 d is the wrong answer...should be c

J
Jayant
11/2/2023 3:15:00 AM

thanks for az 700 dumps

B
Bipul Mishra
12/14/2023 7:12:00 AM

thank you for this tableau dumps . it will helpfull for tableau certification

H
hello
10/31/2023 12:07:00 PM

good content

M
Matheus
9/3/2023 2:14:00 PM

just testing if the comments are real

Y
yenvti2@gmail.com
8/12/2023 7:56:00 PM

very helpful for exam preparation

M
Miguel
10/5/2023 12:16:00 PM

question 11: https://help.salesforce.com/s/articleview?id=sf.admin_lead_to_patient_setup_overview.htm&type=5

N
Noushin
11/28/2023 4:52:00 PM

i think the answer to question 42 is b not c

S
susan sandivore
8/28/2023 1:00:00 AM

thanks for the dump

A
Aderonke
10/31/2023 12:51:00 AM

fantastic assessments

P
Priscila
7/22/2022 9:59:00 AM

i find the xengine test engine simulator to be more fun than reading from pdf.

S
suresh
12/16/2023 10:54:00 PM

nice document

W
Wali
6/4/2023 10:07:00 PM

thank you for making the questions and answers intractive and selectable.

N
Nawaz
7/18/2023 1:10:00 AM

answers are correct?

D
das
6/23/2023 7:57:00 AM

can i belive this dump

S
Sanjay
10/15/2023 1:34:00 PM

great site to practice for sitecore exam

J
jaya
12/17/2023 8:36:00 AM

good for students

B
Bsmaind
8/20/2023 9:23:00 AM

nice practice dumps

K
kumar
11/15/2023 11:24:00 AM

nokia 4a0-114 dumps

V
Vetri
10/3/2023 12:59:00 AM

great content and wonderful to have the answers with explanation

R
Ranjith
8/21/2023 3:39:00 PM

for question #118, the answer is option c. the screen shot is showing the drop down, but the answer is marked incorrectly please update . thanks for sharing such nice questions.

E
Eduardo Ramírez
12/11/2023 9:55:00 PM

the correct answer for the question 29 is d.

D
Dass
11/2/2023 7:43:00 AM

question no 22: correct answers: bc, 1 per session 1 per page 1 per component always

R
Reddy
12/14/2023 2:42:00 AM

these are pretty useful

D
Daisy Delgado
1/9/2023 1:05:00 PM

awesome

A
Atif
6/13/2023 4:09:00 AM

yes please upload

X
Xunil
6/12/2023 3:04:00 PM

great job whoever put this together, for the greater good! thanks!

L
Lakshmi
10/2/2023 5:26:00 AM

just started to view all questions for the exam

R
rani
1/19/2024 11:52:00 AM

helpful material

G
Greg
11/16/2023 6:59:00 AM

hope for the best

H
hi
10/5/2023 4:00:00 AM

will post exam has finished

AI Tutor 👋 I’m here to help!