Exhibit.Refer to the exhibit, which contains a screenshot of some phase 1 settings.The VPN is not up. To diagnose the issue, the administrator enters the following CLI commands on an SSH session on FortiGate:However, the IKE real-time debug does not show any output. Why?
Answer(s): A
To display debug output on FortiGate devices, you must always run both the application-specific debug command and the global debug enable command. The commanddiagnose debug application ike -1sets up the detail level for the IKE daemon debug, but it doesnot display any debug output on its own. As described in the FortiOS CLI debugging manuals, the commanddiagnose debug enableactivates debug output on the console, making all previously set debugs visible. This is especially important for VPN troubleshooting---without the enable command, no output appears even if there is VPN traffic.The correct diagnostic sequence is:diagnose debug application ike -1diagnose debug enableThis procedure is found in every FortiOS CLI debug tutorial and troubleshooting workflow.FortiOS CLI Reference:Debugging VPNs and Real-time Debug OutputFortiGate VPN Troubleshooting Guide: Required Steps for Debug Output
MULTIPLE CHOICEWhich two statements are true regarding heartbeat messages sent from an FSSO collector agent to FortiGate? (Choose two.)
Answer(s): B,C
According to the official Fortinet documentation (Technical Tip: Useful FSSO Commands), heartbeat messages play a crucial role in communication between the FSSO Collector Agent and FortiGate. These messages are regularly sent from the Collector Agent to verify its status, maintain session awareness, and confirm connectivity between the authentication infrastructure and FortiGate appliances.Option B is confirmed by Fortinet, as the collector agent logs on Windows or its management console will specifically note heartbeat events, connection status, and any issues maintaining contact with FortiGate units.Option C is validated by both official CLI documentation and the technical tip linked. On FortiGate, heartbeat messages from the collector agent are visible using real-time debug tools such asdiagnose debug application authdor FSSO-specific commands. These enable administrators to monitor live logon states, session status, and connection health directly from the FortiGate CLI. The debug stream shows heartbeats received and their effect on active logons, associating health monitoring with active sessions.Heartbeat operation is fully automated once FSSO is set up---there is no requirement for manual enablement or configuration, aligning with Fortinet's philosophy of seamless integration and centralized management across the Security Fabric. This ensures that both FortiGate and the collector agent can quickly and reliably detect any miscommunication or outage, addressing authentication issues proactively.Technical Tip: Useful FSSO Commands (Fortinet Community)FortiOS Administration Guide: FSSO, Collector Agent, Heartbeat, CLI Debug
MULTIPLE CHOICERefer to the exhibit, which shows a truncated output of a real-time LDAP debug.What two conclusions can you draw from the output? (Choose two.)
Answer(s): A,D
The exhibit shows these key lines:handle_req-Rcvd auth req ... for jsmith in Lab start_search_dn-base:'DC=TAC,DC=ottawa,DC=fortinet,DC=com' filter:sAMAccountName=jsmith get_all_dn-Found DN 1:CN=John Smith,CN=Users,DC=TAC,DC=ottawa,DC=fortinet,DC=comThe study guide explicitly shows the same LDAP real-time debug pattern and says the request line includes the LDAP server object name:handle_req-Rcvd auth req ... for jsmith in Lab ...That supports A: Lab is the configured LDAP server name being used for this authentication request.For the LDAP flow stage, the study guide states:''An fnbamd_ldap_build_dn_search_req-base message indicates that FortiGate is performing step two: searching for the user in the LDAP tree.'' It also says that if the LDAP server finds the user, the output shows the user's full DN.That matches the exhibit's start_search_dn-base ... filter:sAMAccountName=jsmith and Found DN ... CN=John Smith... lines, so D is correct.Why the other options are wrong:B is wrong because the exhibit shows FortiOS has found the user DN CN=John Smith,..., but that does not mean the user is already authenticating with that DN in this step. The study guide says this DN is discovered in step 2, and only in step 3 does FortiGate bind using the user DN.C is wrong because the exhibit is showing step 2 (Search Request), not step 3 (Bind Request). The study guide separates these steps clearly and shows step 3 with fnbamd_ldap_build_userbind_req-Trying DN ... and __ldap_build_bind_req-Binding to 'CN=John Smith,...'
Refer to the exhibit, which shows a session entry.Which statement about this session is true?
Answer(s): B
The session output reveals a session with proto=1 (ICMP) and the origin and reply directions show address and NAT translations. Specifically, thehook=post dir=org act=snatshows that source NAT is performed for outgoing packets, where the source 10.1.10.10:40602 is translated to 10.200.5.1:8 (likely ICMP id 8, not a TCP/UDP port). The reply direction,hook=pre dir=reply act=dnat, indicates destination NAT for incoming packets: packets incoming for 10.200.5.1:60430 are destination-NATed to 10.1.10.10:40602. The gateway (gwy) is listed as 10.200.1.254/10.1.0.1, which for outgoing traffic means that return traffic is directed to the gateway (10.200.1.254), per the NAT policy. This is confirmed by the FortiOS Session Table Guide, which explains that the returned ICMP reply will be routed out to this NAT gateway. The session statistics and logical flow (SNAT out, matching DNAT in) reinforce that reply traffic to the initiator traverses via 10.200.1.254.FortiOS Administration Guide: Session Table, NAT, and Route InteractionFortinet Technical Note: Diagnose sys session list, Direction and NAT Analysis
Which statement about parallel path processing is correct (PPP)?
Parallel Path Processing (PPP) in FortiOS refers to the system's ability to evaluate and select among multiple processing paths---often involving dedicated network processors, content processors, or CPU-based workflows---to optimally process packets. The official documentation highlights that the PPP engine dynamically selects which hardware or software path to use for each session based on session characteristics, policy configuration, and traffic type. This dynamic selection results in optimal throughput and resource utilization.The document specifies that PPP assesses several processing paths in parallel, using decision logic to determine whether a session should be offloaded to specialist hardware (like NP6, CP9, etc.) or stay in the CPU path, ensuring that each packet is handled by the most efficient available method under current load and policy. Hardware and software configurations both influence this outcome, but it is the PPP engine's decision-making that defines the optimal path per session.Fortinet FortiGate Handbook: Parallel Path ProcessingFortinet FortiOS Technical Documentation: Packet Flow and Path Selection
In IKEv2, which exchange establishes the first CHILD_SA?
Answer(s): D
The correct answer is D. IKE_AUTH.The study guide explicitly states:''IKE_Auth exchange:* Performs the mutual authentication of two IKE endpoints.* Configures settings like IP/mask, DNS, and so on.* Sets up the piggyback of a child SA. Negotiates IP flow and security settings for the IPsec SA.''It also says:''By default, a piggyback child (IPsec) SA is negotiated along with the IKEv2 SA during IKE_AUTH. If additional IPsec SAs are needed ... they are negotiated during subsequent CREATE_CHILD_SA exchanges.''Why the other options are wrong:A . IKE_SA_INIT is incorrect because this exchange negotiates the security settings to protect the IKE traffic, not the first CHILD_SA.B . INFORMATIONAL is incorrect because it is used to convey control messages between IKE endpoints.C . CREATE_CHILD_SA is incorrect for the first CHILD_SA, because it is used to create new additional child SAs or rekey existing ones after the initial exchange.
Which authentication option can you not configure under config user radius on FortiOS?
Accordingto the officialFortinet administrationguide for FortiOS 7.6.4 underthe section 'Configuring aRADIUS server,' the supportedRADIUS authenticationmethods you canconfigure viathe CLI withconfig user radiusare:pap chap mschap mschapv2autoTherelevant CLIsyntax isset auth-type {auto | ms_chap_v2 | ms_chap | chap | pap}.You can confirm this directly inthe configurationtable and fromreal CLI sessions.EAP (Extensible AuthenticationProtocol) isNOT an authenticationoption you candirectly setunderconfig user radius.EAP methods (such as EAP-TLS, EAP-PEAP, EAP-TTLS) are negotiatedbetween the RADIUS client andserver but arenot configurableas an explicitauth-typeoption in FortiOS. EAP authenticationis typicallyused automaticallyby features like802.1X, not throughthe user radiusobject authentication-type setting, and always requiresproper backendworkings betweensupplicant andRADIUS server
MULTIPLE CHOICEExhibit.Refer to the exhibit, which shows a partial output of diagnose hardware aysinfo memory.Which two statements about the output are true? (Choose two.)
Answer(s): B,D
The partial output fromdiagnose hardware sysinfo memoryprovides details on system RAM allocation. According to Fortinet's technical documentation for memory troubleshooting and Linux memory management (which FortiOS is based on):MemFreeis the portion of physical memory not currently allocated to any running process or kernel function. Thus, 708880 kB is available and can be immediately used by user-space programs or system operations.Inactiverefers to pages in the memory cache that were previously in use for I/O or file system buffering but are now not actively referenced. These pages are retained in memory for quick access if needed again, but can be reclaimed for other memory operations if demand increases. The value 98908 kB here represents currently unused cache pages (inactive pages), ready for repurposing or deletion if the system requires more RAM.Cachedrepresents the total amount of system memory allocated to cache, which includes both active and inactive cache pages. It does not, by itself, represent I/O cache exclusively, nor does 'inactive' mean memory ''will never be used'' as the kernel can re-purpose inactive pages on demand.Fortinet Technical Tip: Explaining the 'diagnose hard sysinfo memory' commandFortiOS System Administration Guide: Linux Memory Reporting, Cached and Inactive Statistics
Share your comments for Fortinet NSE7_FSN_AR-7.6 exam with other users:
i have interest to get a sybase iq dba certification
want to pass exm.
are the answers correct?
good morning, could you please upload this exam again, i need it to test my knowledge in sd-wan with version 7.0.
very nice question
i have learning disability and this exam dumps allowed me to focus on the actual questions and not worry about notes and the those other study materials.
165 should be apt
please upload the dumps, real need of them
any recent feeedback?
question number 2 is indicating you are giving proper questions. observe and change properly.
passed today.40% questions were new.litwere case study,lots of new questions on afd,ratelimit,tm,lb,app gatway.got 2 set series of questions which are not present here.questions on azure cyclecloud, no.of vnet/vms required for implimentation,blueprints assignment/management group etc
practice test
want the dumps for emc content management server programming(cmsp)
brilliant and helpful
q75. azure files is pass
very helpful
thank you for these questions. it helped a lot.
how do i get the h12-724 dumps
nice data dumps
answers are correct
good explanation
hi team just want to know if there is any update version of the exam 350-401
helpful on 2017 scrum guide
planning to attempt for the exam.
pleaseee upload
thanks ly so i have information cia
hello team, i need sap qm dumps for practice
it’s good but not senatios based
q.119 - the correct answer is b - they are not captured in an update set as theyre data.
good matter
please upload c_sacp_2308
please upload the dump. thanks very much !!
good questions
hi, could you please update the latest dump version