Cisco® 350-401 Exam (page: 36)
Cisco® Implementing Enterprise Network Core Technologies (ENCOR)
Updated on: 10-Jan-2026

Viewing Page 36 of 214

How does the EIGRP metric differ from the OSPF metric?

  1. The EIGRP metric is calculated based on bandwidth only. The OSPF metric is calculated on delay only.
  2. The EIGRP metric is calculated based on delay only. The OSPF metric is calculated on bandwidth and delay.
  3. The EIGRP metric is calculated based on bandwidth and delay. The OSPF metric is calculated on bandwidth only.
  4. The EIGRP metric is calculated based on hop count and bandwidth. The OSPF metric is calculated on bandwidth and delay.

Answer(s): C

Explanation:

By default, EIGRP metric is calculated:
metric = bandwidth + delay
While OSPF is calculated by:
OSPF metric = Reference bandwidth / Interface bandwidth in bps



Refer to the exhibit.
An engineer is installing a new pair of routers in a redundant configuration.
Which protocol ensures that traffic is not disrupted in the event of a hardware failure?

  1. HSRPv1
  2. GLBP
  3. VRRP
  4. HSRPv2

Answer(s): A

Explanation:

The ג€virtual MAC addressג€ is 0000.0c07.acXX (XX is the hexadecimal group number) so it is using HSRPv1. HSRP Version 2 uses a new MAC address which ranges from 0000.0C9F.F000 to 0000.0C9F.FFFF.



Refer to the exhibit. After an engineer configures an EtherChannel between switch SW1 and switch SW2, this error message is logged on switch SW2:
SW2#
09:45:32: %PM-4-ERR_DISABLE: channel-misconfig error detected on Gi0/0, putting Gi0/0 in err-disable state
09:45:32: %PM-4-ERR_DISABLE: channel-misconfig error detected on Gi0/1, putting Gi0/1 in err-disable state
Based on the output from switch SW1 and the log message received on switch SW2, what action should the engineer take to resolve this issue?

  1. Configure the same protocol on the EtherChannel on switch SW1 and SW2.
  2. Define the correct port members on the EtherChannel on switch SW1.
  3. Correct the configuration error on Interface Gi0/0 on switch SW1.
  4. Correct the configuration error on Interface Gi0/1 on switch SW1.

Answer(s): B



Refer to the exhibit. Communication between London and New York is down.
Which command set must be applied to resolve this issue?

  1. NewYork(config)#int f0/1 NewYork(config)#switchport nonegotiate NewYork(config)#end NewYork#
  2. NewYork(config)#int f0/1 NewYork(config)#switchport mode trunk NewYork(config)#end NewYork#
  3. NewYork(config)#int f0/1 NewYork(config)#switchport trunk encap dot1q NewYork(config)#end NewYork#
  4. NewYork(config)#int f0/1 NewYork(config)#switchport mode dynamic desirable NewYork(config)#end NewYork#

Answer(s): C



Which encryption hashing algorithm does NTP use for authentication?

  1. SSL
  2. MD5
  3. AES128
  4. AES256

Answer(s): B



Viewing Page 36 of 214



Share your comments for Cisco® 350-401 exam with other users:

Big Dog 6/24/2023 4:47:00 PM

question 13 should be dhcp option 43, right?
UNITED STATES


BigMouthDog 1/22/2022 8:17:00 PM

hi team just want to know if there is any update version of the exam 350-401
AUSTRALIA


Desmond 1/5/2023 9:11:00 PM

i just took my oracle exam and let me tell you, this exam dumps was a lifesaver! without them, iam not sure i would have passed. the questions were tricky and the answers were obscure, but the exam dumps had everything i needed. i would recommend to anyone looking to pass their oracle exams with flying colors (and a little bit of cheating) lol.
SINGAPORE


whoAreWeReally 12/19/2023 8:29:00 PM

took the test last week, i did have about 15 - 20 word for word from this site on the test. (only was able to cram 600 of the questions from this site so maybe more were there i didnt review) had 4 labs, bgp, lacp, vrf with tunnels and actually had to skip a lab due to time. lots of automation syntax questions.
EUROPEAN UNION


mrtom33 11/20/2023 4:51:00 AM

i prepared for the eccouncil 350-401 exam. i scored 92% on the test.
Anonymous


Nigora 5/31/2022 10:05:00 PM

this is a beautiful tool. passed after a week of studying.
UNITED STATES