Amazon
Avaya
Cisco
CompTIA
CrowdStrike
EC-Council
EXIN
Fortinet
Google
ISC
ISC2
ITIL
Juniper
Microsoft
NVIDIA
Okta
Palo Alto Networks
Salesforce
SAP
ServiceNow
All Vendors
  1. Home
  2. Cisco
  3. 200-301

Cisco Certified Network Associate (CCNA) 200-301 Exam Questions in PDF

Free Cisco 200-301 Dumps Questions (page: 42)

200-301 PDF — 1395 Questions

In a CDP environment, what happens when the CDP interface on an adjacent device is configured without an IP address?

  1. CDP becomes inoperable on that neighbor
  2. CDP uses the IP address of another interface for that neighbor
  3. CDP operates normally, but it cannot provide IP address information for that neighbor
  4. CDP operates normally, but it cannot provide any information for that neighbor

Answer(s): B



DRAG DROP (Drag and Drop is not supported)
Drag and drop the benefits of a Cisco Wireless Lan Controller from the left onto the correct examples on the right.
Select and Place:

  1. See Explanation section for answer.

Answer(s): A

Explanation:



When configuring an EtherChannel bundle, which mode enables LACP only if a LACP device is detected?

  1. Passive
  2. Desirable
  3. On
  4. Auto
  5. Active

Answer(s): A

Explanation:

The LACP is Link Aggregation Control Protocol. LACP is an open protocol, published under the 802.3ad.
The modes of LACP are active, passive or on. The side configured as “passive” will waiting the other side that should an Active for the Etherchannel to be established.
PAgP is Port-Aggregation Protocol. It is Cisco proprietary protocol. The mode are On, Desirable or Auto. Desirable “" Auto will establish an EtherChannel.
An example of how to configure an Etherchannel:

SwitchFormula1>enable -
SwitchFormula1#configure terminal
SwitchFormula1(config)# interface range f0/5 -14
SwitchFormula1(config-if-range)# channel-group 13 mode ?
active Enable LACP unconditionally
auto Enable PAgP only if a PAgP device is detected
desirable Enable PAgP unconditionally
on Enable Etherchannel only
passive Enable LACP only if a LACP device is detected



Refer to the exhibit. Which VLAN ID is associated with the default VLAN in the given environment?

  1. VLAN 1
  2. VLAN 5
  3. VLAN 10
  4. VLAN 20

Answer(s): A



Which two VLAN IDs indicate a default VLAN? (Choose two.)

  1. 0
  2. 1
  3. 1005
  4. 1006
  5. 4096

Answer(s): B,C

Explanation:

VLAN 1 is a system default VLAN, you can use this VLAN but you cannot delete it. By default VLAN 1 is use for every port on the switch.
Standard VLAN range from 1002-1005 it's Cisco default for FDDI and Token Ring. You cannot delete VLANs 1002-1005. Mostly we don't use VLAN in this range.



Viewing page 42 of 281

Share your comments for Cisco 200-301 exam with other users:

A
Anonymous User
4/14/2026 12:31:34 PM

Question 2:
For question 2, the key concept is the Longest Prefix Match. Routers pick the route whose subnet mask is the most specific (largest prefix length) that still matches the destination IP.
From the options:

  • A) 10.10.10.0/28 ? 10.10.10.0–10.10.10.15
  • B) 10.10.13.0/25 ? 10.10.13.0–10.10.13.127
  • C) 10.10.13.144/28 ? 10.10.13.144–10.10.13.159
  • D) 10.10.13.208/29 ? 10.10.13.208–10.10.13.215

The destination Host A’s IP must fall within 10.10.13.208–10.10.13.215 for the /29 to be the best match. Since /29 is the longest prefix among the matching options, Router1 will use 10.10.13.208/29.
Thus, the correct answer is D.

Canada
Y
yenvti2@gmail.com
8/12/2023 7:56:00 PM

very helpful for exam preparation

Anonymous
X
Xunil
6/12/2023 3:04:00 PM

great job whoever put this together, for the greater good! thanks!

Anonymous
X
x-men
5/23/2023 1:02:00 AM

q23, its an array, isnt it? starts with [ and end with ]. its an array of objects, not object.

UNITED STATES
D
Dan
8/10/2023 4:19:00 PM

question 129 is completely wrong.

UNITED STATES
D
Da_costa
8/1/2023 5:28:00 PM

these are free brain dumps i understand, how can one get free pdf

Anonymous
D
Da Costa
8/27/2023 11:43:00 AM

question 128 the answer should be static not auto

Anonymous
C
CiscoStudent
11/15/2023 5:29:00 AM

in question 272 the right answer states that an autonomous acces point is "configured and managed by the wlc" but this is not what i have learned in my ccna course. is this a mistake? i understand that lightweight aps are managed by wlc while autonomous work as standalones on the wlan.

Anonymous
B
Berihun Desalegn Wonde
7/13/2023 11:00:00 AM

all questions are more important

Anonymous
R
RAWI
7/9/2023 4:54:00 AM

is this dump still valid? today is 9-july-2023

SWEDEN
B
Berihun
7/13/2023 7:29:00 AM

all questions are so important and covers all ccna modules

Anonymous
N
Nico
4/23/2023 11:41:00 PM

my 3rd purcahse from this site. these exam dumps are helpful. very helpful.

ITALY
D
Da Costa
8/25/2023 7:30:00 AM

question 423 eigrp uses metric

Anonymous
G
Gurdeep
1/18/2024 4:00:15 PM

This is one of the most useful study guides I have ever used.

CANADA
AI Tutor 👋 I’m here to help!