Cisco 200-301 Exam (page: 50)
Cisco Certified Network Associate (CCNA)
Updated on: 12-Feb-2026

Viewing Page 50 of 281

When using Rapid PVST+, which command guarantees the switch is always the root bridge for VLAN 200?

  1. spanning-tree vlan 200 priority 614440
  2. spanning-tree vlan 200 priority 0
  3. spanning-tree vlan 200 root primary
  4. spanning-tree vlan 200 priority 38813258

Answer(s): B



Refer to the exhibit. Which command must be executed for Gi1/1 on SW1 to passively become a trunk port if Gi1/1 on SW2 is configured in desirable or trunk mode?

  1. switchport mode dynamic auto
  2. switchport mode dot1-tunnel
  3. switchport mode dynamic desirable
  4. switchport mode trunk

Answer(s): A



Refer to the exhibit. The entire contents or the MAC address table are shown. Sales-4 sends a data frame to Sales-1.


What does the switch do as it receives the frame from Sales-4?

  1. Map the Layer 2 MAC address to the Layer 3 IP address and forward the frame.
  2. Insert the source MAC address and port into the forwarding table and forward the frame to Sales-1.
  3. Perform a lookup in the MAC address table and discard the frame due to a missing entry.
  4. Flood the frame out of all ports except on the port where Sales-1 is connected.

Answer(s): B



Refer to the exhibit. An engineer must configure GigabitEthernet1/1 to accommodate voice and data traffic. Which configuration accomplishes this task?

  1. interface gigabitethernet1/1 switchport mode access switchport access vlan 300 switchport voice vlan 400
  2. interface gigabitethernet1/1 switchport mode trunk switchport trunk vlan 300 switchport trunk vlan 400
  3. interface gigabitethernet1/1 switchport mode access switchport voice vlan 300 switchport access vlan 400
  4. interface gigabitethernet1/1 switchport mode trunk switchport trunk vlan 300 switchport voice vlan 400

Answer(s): A



An engineer needs to add an old switch back into a network. To prevent the switch from corrupting the VLAN database, with action must be taken?

  1. Add the switch in the VTP domain with a lower revision number.
  2. Add the switch in the VTP domain with a higher revision number.
  3. Add the switch with DTP set to dynamic desirable.
  4. Add the switch with DTP set to desirable.

Answer(s): A



Viewing Page 50 of 281



Share your comments for Cisco 200-301 exam with other users:

yenvti2@gmail.com 8/12/2023 7:56:00 PM

very helpful for exam preparation
Anonymous


Xunil 6/12/2023 3:04:00 PM

great job whoever put this together, for the greater good! thanks!
Anonymous


x-men 5/23/2023 1:02:00 AM

q23, its an array, isnt it? starts with [ and end with ]. its an array of objects, not object.
UNITED STATES


Dan 8/10/2023 4:19:00 PM

question 129 is completely wrong.
UNITED STATES


Da_costa 8/1/2023 5:28:00 PM

these are free brain dumps i understand, how can one get free pdf
Anonymous


Da Costa 8/27/2023 11:43:00 AM

question 128 the answer should be static not auto
Anonymous


CiscoStudent 11/15/2023 5:29:00 AM

in question 272 the right answer states that an autonomous acces point is "configured and managed by the wlc" but this is not what i have learned in my ccna course. is this a mistake? i understand that lightweight aps are managed by wlc while autonomous work as standalones on the wlan.
Anonymous


Berihun Desalegn Wonde 7/13/2023 11:00:00 AM

all questions are more important
Anonymous


RAWI 7/9/2023 4:54:00 AM

is this dump still valid? today is 9-july-2023
SWEDEN


Berihun 7/13/2023 7:29:00 AM

all questions are so important and covers all ccna modules
Anonymous


Nico 4/23/2023 11:41:00 PM

my 3rd purcahse from this site. these exam dumps are helpful. very helpful.
ITALY


Da Costa 8/25/2023 7:30:00 AM

question 423 eigrp uses metric
Anonymous


Gurdeep 1/18/2024 4:00:15 PM

This is one of the most useful study guides I have ever used.
CANADA