What is the minimum time a newly created Deduplication storage policy takes to apply to the VMs in the container?
Answer(s): C
https://portal.nutanix.com/page/documents/details?targetId=Prism-Central-Guide- vpc_2023_3:mul-cluster-storage-policy-pc-c.html
Refer to the exhibit.An administrator is adding a new node to a cluster. The node has been imaged to the same versions of AHV and AOS that the cluster running, configured with appropriate IP addresses, and br0-up has been configured the same the existing uplink bondsWhen attempting to add the node to the cluster with the Expand Cluster function in Prism , the cluster is unable to find the new node.Based on the above output from the new node, what is most likely the cause of this issue?
Answer(s): B
The correct answer is B. The existing and the expansion node are on different VLANs.The output shows that the new node has a br0-up bond with four interfaces: eth0, eth1, eth2, and eth. The bond is configured with LACP active and LACP fallback set to false. This means that the bond will only work if the upstream switch supports LACP and is configured to form an LACP group with the four interfaces. However, the output also shows that the bond has no IP address assigned to it, which indicates that the bond is not operational. One possible reason for this is that the existing and the expansion node are on different VLANs, and the upstream switch is not configured to allow the VLAN traffic on the LACP group. This would prevent the new node from communicating with the cluster and being discovered by the Expand Cluster function in Prism.To verify this, the administrator can check the VLAN configuration on the upstream switch and compare it with the existing nodes. Alternatively, the administrator can use the "manage_ovs show_uplinks" command on an existing node and compare the output with the new node. If there is a VLAN mismatch, the administrator can either change the VLAN configuration on the switch or on the new node to match the existing nodes.
Multicloud Infrastructure (NCP-MCI) v6.5 - Nutanix
Refer to the exhibit.An administrator is trying to implement the solution that is shown in the exhibit, but has been unsuccessful.Based on the diagram, what is causing the issue?
The correct answer is C. Network latency.The diagram shows a solution that uses synchronous replication between two remote protection domains, cluster site A and cluster site B. Synchronous replication is a feature that allows near-zero RPO (recovery point objective) by replicating data to the remote site before acknowledging writes to the local site. However, synchronous replication has some requirements and limitations that must be met for it to work properly. One of these requirements is that the network latency between the two sites must be less than or equal to 5 ms. If the network latency is higher than 5 ms, the synchronous replication will fail and the protection policy will be suspended.Therefore, based on the diagram, the most likely cause of the issue is that the network latency between cluster site A and cluster site B is higher than 5 ms, which prevents the synchronous replication from working. To verify this, the administrator can use the "ncli cluster ping" command to measure the network latency between the two sites. If the network latency is indeed higher than 5 ms, the administrator can either improve the network performance or switch to a different replication mode, such as near-synchronous or asynchronous.
Synchronous Replication Requirements
The administrator recently had a node fail in an AHV Nutanix cluster. All of the VMs restarted on other nodes in the cluster, but they discovered that the VMs that make up a SQL cluster were running on the failed host. The administrator has been asked to take measures to prevent a SQL outage in the future.What affinity option will prevent the SQL VMs from running on the same hos?
Answer(s): A
Answer(s): A. VM-VM anti-Affinity policyA VM-VM anti-Affinity policy is a rule that ensures that two or more VMs don't run on the same AHV host. It's useful when an application provides HA and an AHV host can't be an application's single point of failure. In this case, the SQL cluster VMs should have a VM-VM anti-Affinity policy configured to prevent them from running on the same host and causing an outage if that host fails. A VM-VM anti-Affinity policy can be created using the aCLI commands. The other options are not relevant for this scenario.
1: Affinity Policies - Nutanix Support & Insights 2: Affinity Policies Help | Nutanix Community
After logging into Prism Element, an administrator presses the letter A on the Keyboard.What is the expected outcome of this input?
Answer(s): D
API Explorer page will launch when an administrator presses the letter A on the keyboard after logging into Prism Element. This is one of the keyboard shortcuts that Prism Element provides for accessibility and ease of use. API Explorer is a tool that allows users to explore and test Nutanix REST APIs within Prism Element.https://www.nutanixbible.com/3b-book-of-prism-navigation.html
Share your comments for Nutanix NCP-MCI exam with other users:
please upload the question dump for professional machinelearning
question 4 answer is c. this site shows the correct answer as b. "adopt a consumption model" is clearly a cost optimization design principle. looks like im done using this site to study!!!
number 52 answer is d
just started preparing for my exam , and this site is so much help
question 35 is incorrect, the correct answer is c, it even states so: explanation: when a vm is infected with ransomware, you should not restore the vm to the infected vm. this is because the ransomware will still be present on the vm, and it will encrypt the files again. you should also not restore the vm to any vm within the companys subscription. this is because the ransomware could spread to other vms in the subscription. the best way to restore a vm that is infected with ransomware is to restore it to a new azure vm. this will ensure that the ransomware is not present on the new vm.
i would like to take psm1 exam.
cbd and pdb are key to the database
the purchase and download process is very much streamlined. the xengine application is very nice and user-friendly but there is always room for improvement.
please upload p_sapea_2023
anyone use this? the question dont seem to follow other formats and terminology i have been studying im getting worried
good questions
hello are these questions valid for ms-102
some questions are wrongly answered but its good nonetheless
how to get system serial number using intune
is it really helpful to pass the exam
#229 in incorrect - all the customers require an annual review
kindy upload
fantastic assessment on psm 1
56 question correct answer a,b
thank you for providing the q bank
true quesstions
i can´t believe ms asks things like this, seems to be only marketing material.
hi, could you please add the last update of ns0-527
question #3 refers to vnet4 and vnet5. however, there is no vnet5 listed in the case study (testlet 2).
sometimes it may be good some times it may be
qs 4 answer seems wrong- please check
very detailed explanation !
the interactive nature of the test engine application makes the preparation process less boring.
very useful.
complete question dump should be made available for practice.
i just passed my first exam. i got 2 exam dumps as part of the 50% sale. my second exam is under work. once i write that exam i report my result. but so far i am confident.
nice create dewey stefen
i just wrote this exam and it is still valid. the questions are exactly the same but there are about 4 or 5 questions that are answered incorrectly. so watch out for those. best of luck with your exam.
passed my exam today. this is a good start to 2023.
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your NCP-MCI, please sign in or create a free account.