What is the minimum time a newly created Deduplication storage policy takes to apply to the VMs in the container?
Answer(s): C
https://portal.nutanix.com/page/documents/details?targetId=Prism-Central-Guide- vpc_2023_3:mul-cluster-storage-policy-pc-c.html
Refer to the exhibit.An administrator is adding a new node to a cluster. The node has been imaged to the same versions of AHV and AOS that the cluster running, configured with appropriate IP addresses, and br0-up has been configured the same the existing uplink bondsWhen attempting to add the node to the cluster with the Expand Cluster function in Prism , the cluster is unable to find the new node.Based on the above output from the new node, what is most likely the cause of this issue?
Answer(s): B
The correct answer is B. The existing and the expansion node are on different VLANs.The output shows that the new node has a br0-up bond with four interfaces: eth0, eth1, eth2, and eth. The bond is configured with LACP active and LACP fallback set to false. This means that the bond will only work if the upstream switch supports LACP and is configured to form an LACP group with the four interfaces. However, the output also shows that the bond has no IP address assigned to it, which indicates that the bond is not operational. One possible reason for this is that the existing and the expansion node are on different VLANs, and the upstream switch is not configured to allow the VLAN traffic on the LACP group. This would prevent the new node from communicating with the cluster and being discovered by the Expand Cluster function in Prism.To verify this, the administrator can check the VLAN configuration on the upstream switch and compare it with the existing nodes. Alternatively, the administrator can use the "manage_ovs show_uplinks" command on an existing node and compare the output with the new node. If there is a VLAN mismatch, the administrator can either change the VLAN configuration on the switch or on the new node to match the existing nodes.
Multicloud Infrastructure (NCP-MCI) v6.5 - Nutanix
Refer to the exhibit.An administrator is trying to implement the solution that is shown in the exhibit, but has been unsuccessful.Based on the diagram, what is causing the issue?
The correct answer is C. Network latency.The diagram shows a solution that uses synchronous replication between two remote protection domains, cluster site A and cluster site B. Synchronous replication is a feature that allows near-zero RPO (recovery point objective) by replicating data to the remote site before acknowledging writes to the local site. However, synchronous replication has some requirements and limitations that must be met for it to work properly. One of these requirements is that the network latency between the two sites must be less than or equal to 5 ms. If the network latency is higher than 5 ms, the synchronous replication will fail and the protection policy will be suspended.Therefore, based on the diagram, the most likely cause of the issue is that the network latency between cluster site A and cluster site B is higher than 5 ms, which prevents the synchronous replication from working. To verify this, the administrator can use the "ncli cluster ping" command to measure the network latency between the two sites. If the network latency is indeed higher than 5 ms, the administrator can either improve the network performance or switch to a different replication mode, such as near-synchronous or asynchronous.
Synchronous Replication Requirements
The administrator recently had a node fail in an AHV Nutanix cluster. All of the VMs restarted on other nodes in the cluster, but they discovered that the VMs that make up a SQL cluster were running on the failed host. The administrator has been asked to take measures to prevent a SQL outage in the future.What affinity option will prevent the SQL VMs from running on the same hos?
Answer(s): A
Answer(s): A. VM-VM anti-Affinity policyA VM-VM anti-Affinity policy is a rule that ensures that two or more VMs don't run on the same AHV host. It's useful when an application provides HA and an AHV host can't be an application's single point of failure. In this case, the SQL cluster VMs should have a VM-VM anti-Affinity policy configured to prevent them from running on the same host and causing an outage if that host fails. A VM-VM anti-Affinity policy can be created using the aCLI commands. The other options are not relevant for this scenario.
1: Affinity Policies - Nutanix Support & Insights 2: Affinity Policies Help | Nutanix Community
After logging into Prism Element, an administrator presses the letter A on the Keyboard.What is the expected outcome of this input?
Answer(s): D
API Explorer page will launch when an administrator presses the letter A on the keyboard after logging into Prism Element. This is one of the keyboard shortcuts that Prism Element provides for accessibility and ease of use. API Explorer is a tool that allows users to explore and test Nutanix REST APIs within Prism Element.https://www.nutanixbible.com/3b-book-of-prism-navigation.html
Share your comments for Nutanix NCP-MCI exam with other users:
helpful material
hope for the best
will post exam has finished
really correct and good analyze!
excellent thanks a lot
will post once pass the cka exam
good content
q:32 answer has to be option c
nice questions
i really like the support team in this website. they are fast in communication and very helpful.
a good contemporary exam review
q23, its an array, isnt it? starts with [ and end with ]. its an array of objects, not object.
cool very helpfull
i just passed. this exam dumps is the same one from prepaway and examcollection. it has all the real test questions.
is this a valid prince2 practitioner dumps?
all are relatable questions
might help me to prepare for the exam
just paid and downlaod the 2 exams using the 50% sale discount. so far i was able to download the pdf and the test engine. all looks good.
i think it should be a,c. option d goes against the principle of building anything custom unless there are no work arounds available
very legible
is this exam accurate or helpful?
please upload dump, i have exam in 2 days
this is useful
question 232 answer should be perimeter not netowrk layer. wrong answer selected
hi team, could you please provide this dump ?
very helpful to clear the exam and understand the concept.
i think it is great that you are helping people when they need it. thanks.
cannot evaluate yet
a laptops wireless antenna is most likely located in the bezel of the lid
good examplae to learn basic
this is useful information
looks usefull
question 81 should be c.
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your NCP-MCI, please sign in or create a free account.