F-OFDM over the NR air interface uses flexible subcarrier spacing to meet the requirements of different 5G service scenarios. Which of the following types of subcarrier spacing is not supported by Sub6G?
Answer(s): A
F-OFDM (Filtered Orthogonal Frequency Division Multiplexing) over the NR air interface uses flexible subcarrier spacing to meet the requirements of different 5G service scenarios. F-OFDM is a 5G physical layer waveform that is designed to provide high spectral efficiency, low complexity and low latency. It uses a flexible subcarrier spacing, which can be adjusted to meet the requirements of different 5G services. The subcarrier spacing can be 15KHz, 30KHz, 60KHz, or 120KHz. Sub-6GHz 5G networks are designed to provide wide-area coverage and support high data rate services such as mobile broadband, IoT, and critical communications. Sub-6GHz band is mainly used for 5G deployment in rural areas, and in-building coverage.Therefore, the subcarrier spacing that is not supported by Sub-6GHz is 120KHz. So the correct answer is A. 120KHz. It's worth noting that each subcarrier spacing has its own advantages and disadvantages. 120KHz spacing is mainly used for low mobility services such as fixed wireless access, while 15KHz spacing is mainly used for high mobility services such as mobile broadband.
The mmWave range is new for NR. It supports the largest bandwidth in a cell but has poor coverage capabilities. It requires high performance from RF components and generally applies only to line of sight (LOS) coverage.
The mmWave range is a new spectrum range for 5G NR, and it supports the largest bandwidth in a cell. However, it has poor coverage capabilities, as it requires high performance from RF components and generally applies only to line of sight (LOS) coverage. This makes it challenging to use in many applications, as it requires careful planning and implementation in order to ensure effective coverage.https://www.gsma.com/futurenetworks/wiki/5g-implementation-guidelines/ 5G Implementation Guidelines: NSA Option 3 - Future Networks https://www.gsma.com/futurenetworks/wiki/5g-implementation-guidelines/ https://www.ericsson.com/en/ran5G RAN - Radio Access Networks - Ericsson https://www.ericsson.com/en/ran https://www.5gamericas.org/wp-content/uploads/2020/12/InDesign-Understanding-mmWave-for- 5G-Networks.pdfUnderstanding mmWave for 5G Networks 1 - 5G Americas https://www.5gamericas.org/wp-content/uploads/2020/12/InDesign-Understanding-mmWave-for- 5G-Networks.pdfThe millimeter wave (mmWave) range is new for 5G NR (New Radio). It supports the largest bandwidth in a cell but has poor coverage capabilities. It requires high performance from RFcomponents and generally applies only to line of sight (LOS) coverage. The mmWave range is considered to be the higher frequency range of the 5G spectrum and it includes frequencies above 24GHz, such as 28GHz, 38GHz and 60GHz. These frequencies offer a large amount of bandwidth, which is necessary to support high-data rate services, such as ultra-high- definition video streaming, virtual reality, and the internet of things. However, the mmWave range has poor coverage capabilities because the signals are easily blocked by obstacles such as buildings and trees, and they also have a shorter propagation distance than lower frequency bands. Therefore, mmWave range is generally used for high-density urban areas, and indoor environments.Additionally, RF components for mmWave have to meet high performance requirements, such as high linearity, high gain and high power handling capability. Also, the mmWave signals are highly sensitive to the presence or absence of a clear line of sight (LOS) between the transmitter and the receiver, which makes it less reliable for non-line-of-sight (NLOS) coverage.
Which of the following statements about the NR slot structure are correct? (Choose All that Apply)
Answer(s): A,B,D
1. NR downlink slots are used to transmit downlink data and control information, such as channel state information (CSI) and downlink control information (DCI). B. Downlink self-contained slots are also called as "Downlink Shared Channels (DL-SCH) slots", they can be used to transmit downlink data, but also can be used to transmit uplink control information (UCI) and sounding reference signals (SRS) in the downlink direction.2. The symbols in a slot can be classified as downlink, uplink, or flexible, meaning that the symbols can be used to transmit data in either direction, or to transmit control information. It's worth noting that the NR slot structure is designed to be flexible and efficient, it allows for a variable slot duration and a variable number of symbols, depending on the subcarrier spacing and the number of resource blocks used. This flexibility is intended to support a wide range of services and traffic types.
5G inherits the frame structure of 4G, but the slot length can be adjusted based on different SCSs.Which of the following is not a 5G slot length?
Answer(s): B
5G inherits the frame structure of 4G, but the slot length can be adjusted based on different subcarrier spacings (SCSs). The 5G slot length can be adjusted from 0.25ms to 1ms, with each slot containing one or more symbols.The shorter the slot length, the higher the frequency and the less the coverage, but it allows for more efficient use of resources and higher data rates. The longer the slot length, the lower the frequency, the better the coverage, but it's less efficient in terms of resource usage and data rate. So, the correct answer is B. 10ms, is not a 5G slot length. It's worth noting that the 5G standard defines several slot lengths, and the choice of slot length depends on the specific use case and the requirements of the service being supported.
Which of the following parameters is related to the frequency-domain position of PBCH DMRSs?
PCI (Physical Cell Identity) is related to the frequency-domain position of PBCH DMRSs (Physical Broadcast Channel Demodulation Reference Signals)The PBCH DMRSs are used to demodulate the Physical Broadcast Channel (PBCH) which contains system information such as the cell identity, system bandwidth, and the downlink carrier frequency. The PBCH DMRSs are transmitted in the frequency domain, and their position is determined by the Physical Cell Identity (PCI). The PCI is a unique identifier assigned to each cell in the network, and it's used to identify the cell and its system information.So, the correct answer is B. PCI. It's worth noting that the other parameters you mentioned are also related to the 5G system information and the cell configuration. Cell ID is a unique identifier assigned to each cell, SI-RNTI (System Information RNTI) is a unique identifier assigned to the system information, and Bandwidth is the amount of frequency resources allocated to the cell.
Share your comments for Huawei H35-480_V3.0 exam with other users:
looking for cphq dumps, where can i find these for free? please and thank you.
@aarun , thanks for the information. it would be great help if you share your email
1z0-1078-23 need this dumps
i gave the microsoft azure az-500 tests and prepared from this site as it has latest mock tests available which helped me evaluate my performance and score 919/1000
i cannot see the button to go to the questions
good questions
q-6 ans-b correct. https://docs.paloaltonetworks.com/pan-os/9-1/pan-os-cli-quick-start/use-the-cli/commit-configuration-changes
very nice very nice
please help us with 1z0-1107-2 dumps
please upload the practice questions
need this dumps
preparing for this exam is overwhelming. you cannot pass without the help of these exam dumps.
new to this site but i feel it is good
the correct answer to q8 is b. explanation since the mule app has a dependency, it is necessary to include project modules and dependencies to make sure the app will run successfully on the runtime on any other machine. source code of the component that the mule app is dependent of does not need to be included in the exported jar file, because the source code is not being used while executing an app. compiled code is being used instead.
Delayed the exam until December 29th.
A and D are True
good one with explanation
This is one of the most useful study guides I have ever used.
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your H35-480_V3.0, please sign in or create a free account.