F-OFDM over the NR air interface uses flexible subcarrier spacing to meet the requirements of different 5G service scenarios. Which of the following types of subcarrier spacing is not supported by Sub6G?
Answer(s): A
F-OFDM (Filtered Orthogonal Frequency Division Multiplexing) over the NR air interface uses flexible subcarrier spacing to meet the requirements of different 5G service scenarios. F-OFDM is a 5G physical layer waveform that is designed to provide high spectral efficiency, low complexity and low latency. It uses a flexible subcarrier spacing, which can be adjusted to meet the requirements of different 5G services. The subcarrier spacing can be 15KHz, 30KHz, 60KHz, or 120KHz. Sub-6GHz 5G networks are designed to provide wide-area coverage and support high data rate services such as mobile broadband, IoT, and critical communications. Sub-6GHz band is mainly used for 5G deployment in rural areas, and in-building coverage.Therefore, the subcarrier spacing that is not supported by Sub-6GHz is 120KHz. So the correct answer is A. 120KHz. It's worth noting that each subcarrier spacing has its own advantages and disadvantages. 120KHz spacing is mainly used for low mobility services such as fixed wireless access, while 15KHz spacing is mainly used for high mobility services such as mobile broadband.
The mmWave range is new for NR. It supports the largest bandwidth in a cell but has poor coverage capabilities. It requires high performance from RF components and generally applies only to line of sight (LOS) coverage.
The mmWave range is a new spectrum range for 5G NR, and it supports the largest bandwidth in a cell. However, it has poor coverage capabilities, as it requires high performance from RF components and generally applies only to line of sight (LOS) coverage. This makes it challenging to use in many applications, as it requires careful planning and implementation in order to ensure effective coverage.https://www.gsma.com/futurenetworks/wiki/5g-implementation-guidelines/ 5G Implementation Guidelines: NSA Option 3 - Future Networks https://www.gsma.com/futurenetworks/wiki/5g-implementation-guidelines/ https://www.ericsson.com/en/ran5G RAN - Radio Access Networks - Ericsson https://www.ericsson.com/en/ran https://www.5gamericas.org/wp-content/uploads/2020/12/InDesign-Understanding-mmWave-for- 5G-Networks.pdfUnderstanding mmWave for 5G Networks 1 - 5G Americas https://www.5gamericas.org/wp-content/uploads/2020/12/InDesign-Understanding-mmWave-for- 5G-Networks.pdfThe millimeter wave (mmWave) range is new for 5G NR (New Radio). It supports the largest bandwidth in a cell but has poor coverage capabilities. It requires high performance from RFcomponents and generally applies only to line of sight (LOS) coverage. The mmWave range is considered to be the higher frequency range of the 5G spectrum and it includes frequencies above 24GHz, such as 28GHz, 38GHz and 60GHz. These frequencies offer a large amount of bandwidth, which is necessary to support high-data rate services, such as ultra-high- definition video streaming, virtual reality, and the internet of things. However, the mmWave range has poor coverage capabilities because the signals are easily blocked by obstacles such as buildings and trees, and they also have a shorter propagation distance than lower frequency bands. Therefore, mmWave range is generally used for high-density urban areas, and indoor environments.Additionally, RF components for mmWave have to meet high performance requirements, such as high linearity, high gain and high power handling capability. Also, the mmWave signals are highly sensitive to the presence or absence of a clear line of sight (LOS) between the transmitter and the receiver, which makes it less reliable for non-line-of-sight (NLOS) coverage.
Which of the following statements about the NR slot structure are correct? (Choose All that Apply)
Answer(s): A,B,D
1. NR downlink slots are used to transmit downlink data and control information, such as channel state information (CSI) and downlink control information (DCI). B. Downlink self-contained slots are also called as "Downlink Shared Channels (DL-SCH) slots", they can be used to transmit downlink data, but also can be used to transmit uplink control information (UCI) and sounding reference signals (SRS) in the downlink direction.2. The symbols in a slot can be classified as downlink, uplink, or flexible, meaning that the symbols can be used to transmit data in either direction, or to transmit control information. It's worth noting that the NR slot structure is designed to be flexible and efficient, it allows for a variable slot duration and a variable number of symbols, depending on the subcarrier spacing and the number of resource blocks used. This flexibility is intended to support a wide range of services and traffic types.
5G inherits the frame structure of 4G, but the slot length can be adjusted based on different SCSs.Which of the following is not a 5G slot length?
Answer(s): B
5G inherits the frame structure of 4G, but the slot length can be adjusted based on different subcarrier spacings (SCSs). The 5G slot length can be adjusted from 0.25ms to 1ms, with each slot containing one or more symbols.The shorter the slot length, the higher the frequency and the less the coverage, but it allows for more efficient use of resources and higher data rates. The longer the slot length, the lower the frequency, the better the coverage, but it's less efficient in terms of resource usage and data rate. So, the correct answer is B. 10ms, is not a 5G slot length. It's worth noting that the 5G standard defines several slot lengths, and the choice of slot length depends on the specific use case and the requirements of the service being supported.
Which of the following parameters is related to the frequency-domain position of PBCH DMRSs?
PCI (Physical Cell Identity) is related to the frequency-domain position of PBCH DMRSs (Physical Broadcast Channel Demodulation Reference Signals)The PBCH DMRSs are used to demodulate the Physical Broadcast Channel (PBCH) which contains system information such as the cell identity, system bandwidth, and the downlink carrier frequency. The PBCH DMRSs are transmitted in the frequency domain, and their position is determined by the Physical Cell Identity (PCI). The PCI is a unique identifier assigned to each cell in the network, and it's used to identify the cell and its system information.So, the correct answer is B. PCI. It's worth noting that the other parameters you mentioned are also related to the 5G system information and the cell configuration. Cell ID is a unique identifier assigned to each cell, SI-RNTI (System Information RNTI) is a unique identifier assigned to the system information, and Bandwidth is the amount of frequency resources allocated to the cell.
Share your comments for Huawei H35-480_V3.0 exam with other users:
question 16: https://help.salesforce.com/s/articleview?id=sf.care_console_overview.htm&type=5
yes i m prepared exam
my experience was great with this site as i studied for the ms-900 from here and got 900/1000 on the test. my main focus was on the tutorials which were provided and practice questions. thanks!
great course
very good question
question: 93 which statement is true regarding the result? sales contain 6 columns and values contain 7 columns so c is not right answer.
highly recommend just passed my exam.
great practice! thanks
anyone who wrote this exam recently?
kindly share the dump
could you please upload cfe fraud prevention and deterrence questions? it will be very much helpful.
this is really very very helpful for mcd level 1
very helpful!
question #18s answer should be a, not d. this should be corrected. it should be minvalidityperiod
thanks for the exact solution
need to refer the questions and have to give the exam
i need it right now if it was possible please
i need it very much please share it in the fastest time.
correct answer is d for student.java program
q:37 c is correct
q6 exam topic: terramearth, c: correct answer: copy 1petabyte to encrypted usb device ???
explained answers
plan to take theaws certified developer - associate dva-c02 in the next few weeks
very helpfull
good questions
help to practice csa exam
nice tip and well documented
i need the exam
please upload
prepping for fsc exam
pd1 with great experience
@t it seems like azure service bus message quesues could be the best solution
helpful to check your understanding.
question 128 the answer should be static not auto
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your H35-480_V3.0, please sign in or create a free account.