Refer to the exhibit, which shows a Branch1 configuration and routing table.In the SD-WAN implicit rule, you do not want the traffic load balance for the overlay interface when all members are available.In this scenario, which configuration change will meet this requirement?
Answer(s): D
The default load balancing mode for the SD-WAN implicit rule is source IP based. This means that traffic will be load balanced evenly between the overlay members, regardless of the member's priority.To prevent traffic from being load balanced, you can configure the priority of each overlay member to 10. This will make the member ineligible for load balancing. The other options are not correct. Changing the load balancing mode to source-IP based will still result in traffic being load balanced. Creating a new static route with the internet sdwan-zone only will not affect the load balancing of the overlay interface. Configuring the cost in each overlay member to 10 will also not affect the load balancing, as the cost is only used when the implicit rule cannot find a match for the destination IP address.https://docs.fortinet.com/document/fortigate/6.4.0/sd-wan-deployment-for- mssps/775385/defining-interface-members
Refer to the exhibits.An administrator has configured a FortiGate and Forti Authenticator for two-factor authentication with FortiToken push notifications for their SSL VPN login. Upon initial review of the setup, the administrator has discovered that the customers can manually type in their two-factor code and authenticate but push notifications do not workBased on the information given in the exhibits, what must be done to fix this?
https://community.fortinet.com/t5/FortiAuthenticator/Technical-Tip-FortiToken-Push-on- FortiAuthenticator-operation/ta-p/190810
Refer to the exhibit.A customer has deployed a FortiGate 300E with virtual domains (VDOMs) enabled in the multi- VDOM mode. There are three VDOMs: Root is for management and internet access, while VDOM 1 and VDOM 2 are used for segregating internal traffic. AccountVInk and SalesVInk are standard VDOM links in Ethernet mode.Given the exhibit, which two statements below about VDOM behavior are correct? (Choose two.)
Answer(s): A,B
You are responsible for recommending an adapter type for NICs on a FortiGate VM that will run on an ESXi Hypervisor. Your recommendation must consider performance as the main concern, cost is not a factor. Which adapter type for the NICs will you recommend?
The FortiGate VM is a virtual firewall appliance that can run on various hypervisors, such as ESXi, Hyper-V, KVM, etc. The adapter type for NICs on a FortiGate VM determines the performance and compatibility of the network interface cards with the hypervisor and the physical network. There are different adapter types available for NICs on a FortiGate VM, such as E1000, VMXNET3, SR-IOV, etc. If performance is the main concern and cost is not a factor, one option is to use native ESXi networking with VMXNET3 adapter type for NICs on a FortiGate VM that will run on an ESXi hypervisor. VMXNET3 is a paravirtualized network interface card that is optimized for performance in virtual machines and supports features such as multiqueue support, Receive Side Scaling (RSS), Large Receive Offload (LRO), IPv6 offloads, and MSI/MSI-X interrupt delivery. Native ESXi networking means that the FortiGate VM uses the standard virtual switch (vSwitch) or distributed virtual switch (dvSwitch) provided by the ESXi hypervisor to connect to the physical network. This option can provide high performance and compatibility for NICs on a FortiGate VM without requiring additional hardware or software components.
https://docs.fortinet.com/document/fortigate/7.0.0/vm-installation-for-vmware- esxi/19662/installing-fortigate-vm-on-vmware-esxi https://docs.fortinet.com/document/fortigate/7.0.0/vm-installation-for-vmware- esxi/19662/networking
You are deploying a FortiExtender (FEX) on a FortiGate-60F. The FEX will be managed by the FortiGate. You anticipate high utilization. The requirement is to minimize the overhead on the device for WAN traffic.Which action achieves the requirement in this scenario?
Answer(s): C
VLAN Mode is a more efficient way to connect a FortiExtender to a FortiGate than CAPWAP Mode. This is because VLAN Mode does not require the FortiExtender to send additional control traffic to the FortiGate.The other options are not correct.A . Add a switch between the FortiGate and FEX. This will add overhead to the network, as the switch will need to process the traffic.B . Enable CAPWAP connectivity between the FortiGate and the FortiExtender. This will increase the overhead on the FortiGate, as it will need to process additional control traffic. D . Add a VLAN under the FEX-WAN interface on the FortiGate. This will not affect the overhead on the FortiGate.http://docs.fortinet.com/document/fortiextender/7.0.3/admin-guide-fgt-managed/394272/vlan- mode http://docs.fortinet.com/document/fortiextender/7.0.3/admin-guide-fgt-managed/618684/vlan- mode-and-performance
Share your comments for Fortinet NSE8_812 exam with other users:
this is useful
question 232 answer should be perimeter not netowrk layer. wrong answer selected
nice questions
hi team, could you please provide this dump ?
very helpful to clear the exam and understand the concept.
i think it is great that you are helping people when they need it. thanks.
cannot evaluate yet
a laptops wireless antenna is most likely located in the bezel of the lid
good examplae to learn basic
this is useful information
looks usefull
question 81 should be c.
question 18 : response isnt a ?
plaese add questions
is dumps still valid ?
thanks for this
please upload questions
please upload the question dump for professional machinelearning
question 4 answer is c. this site shows the correct answer as b. "adopt a consumption model" is clearly a cost optimization design principle. looks like im done using this site to study!!!
number 52 answer is d
just started preparing for my exam , and this site is so much help
question 35 is incorrect, the correct answer is c, it even states so: explanation: when a vm is infected with ransomware, you should not restore the vm to the infected vm. this is because the ransomware will still be present on the vm, and it will encrypt the files again. you should also not restore the vm to any vm within the companys subscription. this is because the ransomware could spread to other vms in the subscription. the best way to restore a vm that is infected with ransomware is to restore it to a new azure vm. this will ensure that the ransomware is not present on the new vm.
i would like to take psm1 exam.
cbd and pdb are key to the database
the purchase and download process is very much streamlined. the xengine application is very nice and user-friendly but there is always room for improvement.
please upload p_sapea_2023
anyone use this? the question dont seem to follow other formats and terminology i have been studying im getting worried
good questions
hello are these questions valid for ms-102
some questions are wrongly answered but its good nonetheless
how to get system serial number using intune
is it really helpful to pass the exam
#229 in incorrect - all the customers require an annual review
kindy upload
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your NSE8_812, please sign in or create a free account.