Refer to the exhibit, which shows a truncated output of a real-time RADIUS debug.Which two statements are true? (Choose two.)
Answer(s): A,B
RADIUS Server IP Address:The debug output shows that the RADIUS request was sent to the server at IP=172.25.188.164. This indicates that the RADIUS server being queried for authentication is indeed located at this IP address.Authentication Result:The debug output includes a line indicating the result for the RADIUS server: Result for radius svr 'RadiusServer' 172.25.188.164(0) is 0. A result code of 0 typically signifies that the authentication attempt was unsuccessful.Authentication Scheme:The debug output does not indicate that the authentication scheme used was pop3; it mentions using CHAP (Challenge Handshake Authentication Protocol).Two-factor Authentication:There is no indication in the debug output that two-factor authentication was required for this session.
Fortinet Network Security 7.2 Support Engineer DocumentationRADIUS Authentication Configuration and Debugging Guides
Which three conditions are required for two FortiGate devices to form an OSPF adjacency? (Choose three.)
Answer(s): C,D,E
OSPF Interface Network Types:The network types of the interfaces on both FortiGate devices must match. Common network types include broadcast, point-to-point, and non-broadcast multi-access (NBMA).Authentication Settings:Both devices must have matching authentication settings (if authentication is used). This includes the same authentication type (none, simple password, or MD5) and the same password or key.OSPF Router IDs:Each OSPF router must have a unique router ID within the OSPF domain. The router ID is typically an IPv4 address selected from one of the router's interfaces or manually configured.Link Costs and Interface Priority:While link costs and interface priorities are important for route selection and designated router (DR) elections, they do not prevent OSPF adjacency formation if they differ.
Fortinet Network Security 7.2 Support Engineer DocumentationOSPF Configuration Guides
Refer to the exhibit, which contains the partial output of a diagnose command.Based on the output, which two statements are correct? (Choose two.)
Answer(s): A,D
Remote Gateway IP:The output shows 10.200.5.1 as the remote gateway IP, confirming that this is the IP address of the remote gateway involved in the IPsec VPN tunnel.Quick Mode Selectors:The quick mode selectors specify the subnets involved in the VPN. The output shows src:0:10.1.2.0/255.255.255.0:0 and dst: 0:10.1.1.0/255.255.255.0:0, indicating the subnets being tunneled.DPD (Dead Peer Detection):DPD is shown as mode=on-demand on=1 idle=20000ms retry=3 count=0 seqno=0, indicating that DPD is enabled in on-demand mode.Anti-replay:The output includes replaywin=2048 and replaywin_lastseq=00000000, which are indicators that anti-replay protection is enabled for the IPsec tunnel.
Fortinet Network Security 7.2 Support Engineer DocumentationVPN Configuration and Diagnostic Guides
Refer to the exhibit, which shows a session table entry.Which statement about FortiGate behavior relating to this session is true?
Answer(s): B
The session table entry provided shows detailed information about a specific network session passing through the FortiGate device. From the session details, we can see that the session has various attributes such as state, protocol, policy, and inspection details.The session state (proto_state=11) indicates that the session is being actively processed and inspected.The npd_state=00000000 suggests that the session is being handled by the CPU rather than offloaded to a Network Processor (NP).The session is marked for security profile inspection, evident from the detailed byte/packet counts and other session parameters.From these indicators, it's clear that FortiGate is using its CPU to perform security profile inspection on this session rather than simply forwarding the traffic without inspection or relying solely on IPS inspection.
Fortinet Documentation on Session TableFortinet Community Discussion on Session Table
What is the diagnose test application ipsmonitor 5 command used for?
Answer(s): C
The command diagnose test application ipsmonitor 5 is used to restart all IPS (Intrusion Prevention System) engines and monitors on the FortiGate device. This command is part of the diagnostic tools available for troubleshooting and maintaining the IPS functionality on the FortiGate.Running this command forces the IPS system to reset and reinitialize, which can be useful in situations where the IPS functionality appears to be malfunctioning or not responding correctly.This action helps in clearing any issues that might have arisen due to internal errors or misconfigurations, ensuring that the IPS engines operate correctly after the restart.
Share your comments for Fortinet NSE7_NST-7.2 exam with other users:
good content
understanding about joins
please upload oracle cloud infrastructure 2023 foundations associate exam braindumps. thank you.
questions made studying easy and enjoyable, passed on the first try!
has anyone recently attended safe 6.0 exam? did you see any questions from here?
question 13 should be dhcp option 43, right?
the buy 1 get 1 is a great deal. so far i have only gone over exam. it looks promissing. i report back once i write my exam.
is this dump good
good ................
passed
yes going good
good questions for practice
need dump and sap notes for c_s4cpr_2308 - sap certified application associate - sap s/4hana cloud, public edition - sourcing and procurement
question 11: d i personally feel some answers are wrong.
nice questions
looking for c1000-158: ibm cloud technical advocate v4 questions
can you share the pdf
admin ii is real technical stuff
could you post the link
hello send me dumps
it is very nice
i gave the amazon dva-c02 tests today and passed. very helpful.
there is an incorrect word in the problem statement. for example, in question 1, there is the word "speci c". this is "specific. in the other question, there is the word "noti cation". this is "notification. these mistakes make this site difficult for me to use.
passed my az-120 certification exam today with 90% marks. studied using the dumps highly recommended to all.
i need it, plz make it available
q47: intrusion prevention system is the correct answer, not patch management. by definition, there are no patches available for a zero-day vulnerability. the way to prevent an attacker from exploiting a zero-day vulnerability is to use an ips.
this is simple but tiugh as well
questão 4, segundo meu compilador local e o site https://www.jdoodle.com/online-java-compiler/, a resposta correta é "c" !
its very useful
i mastered my skills and aced the comptia 220-1102 exam with a score of 920/1000. i give the credit to for my success.
real questions
very helpful assessments
hi there, i would like to get dumps for this exam
i studied for the microsoft azure az-204 exam through it has 100% real questions available for practice along with various mock tests. i scored 900/1000.