Fortinet FCSS - Enterprise Firewall 7.6 Administrator FCSS_EFW_AD-7.6 Dumps in PDF

Free Fortinet FCSS_EFW_AD-7.6 Real Questions (page: 14)

What does the command set forward-domain <domain_ID> in a transparent VDOM interface do?

  1. It configures the interface to prioritize traffic based on the domain ID, enhancing quality of service for specified VLANs.
  2. It isolates traffic within a specific VLAN by assigning a broadcast domain to an interface based on the VLAN ID.
  3. It restricts the interface to managing traffic only from the specified VLAN, effectively segregating network traffic.
  4. It assigns a unique domain ID to the interface, allowing it to operate across multiple VLANs within the same VDOM.

Answer(s): B

Explanation:

In a transparent mode Virtual Domain (VDOM) configuration, FortiGate operates as a Layer 2 bridge rather than performing Layer 3 routing. The set forward-domain <domain_ID> command is used to control how traffic is forwarded between interfaces within the same transparent VDOM.
A forward-domain acts as a broadcast domain, meaning only interfaces with the same forward-domain ID can exchange traffic. This setting is commonly used to separate different VLANs or network segments within the transparent VDOM while still allowing FortiGate to apply security policies.



Refer to the exhibit, which shows a physical topology and a traffic log.

The administrator is checking on FortiAnalyzer traffic from the device with IP address 10.1.10.1, located behind the FortiGate ISFW device.
The firewall policy in on the ISFW device does not have UTM enabled and the administrator is surprised to see a log with the action Malware, as shown in the exhibit.
What are the two reasons FortiAnalyzer would display this log? (Choose two.)

  1. Security rating is enabled in ISFW.
  2. ISFW is in a Security Fabric environment.
  3. ISFW is not connected to FortiAnalyzer and must go through NGFW-1.
  4. The firewall policy in NGFW-1 has UTM enabled.

Answer(s): B,D

Explanation:

From the exhibit, ISFW is part of a Security Fabric environment with NGFW-1 as the Fabric Root. In this architecture, FortiGate devices share security intelligence, including logs and detected threats.
ISFW is in a Security Fabric environment:
●Security Fabric allows devices like ISFW to receive threat intelligence from NGFW-1, even if UTM is not enabled locally.
●If NGFW-1 detects malware from IP 10.1.10.1 to 89.238.73.97, this information can be propagated to ISFW and FortiAnalyzer.
The firewall policy in NGFW-1 has UTM enabled:
●Even though ISFW does not have UTM enabled, NGFW-1 (which sits between ISFW and the external network) does have UTM enabled and is scanning traffic.
●Since NGFW-1 detects malware in the session, it logs the event, which is then sent to FortiAnalyzer.



Refer to the exhibit, which contains a partial VPN configuration.

What can you conclude from this VPN IPsec phase 1 configuration?

  1. This configuration is the best for networks with regular traffic intervals, providing a balance between connectivity assurance and resource utilization.
  2. Peer IDs are unencrypted and exposed, creating a security risk.
  3. FortiGate will not add a route to its routing or forwarding information base when the dynamic tunnel is negotiated.
  4. A separate interface is created for each dial-up tunnel, which can be slower and more resource intensive, especially in large networks.

Answer(s): A

Explanation:

This IPsec Phase 1 configuration defines a dynamic VPN tunnel that can accept connections from multiple peers. The settings chosen here suggest a configuration optimized for networks with intermittent traffic patterns while ensuring resources are used efficiently.
Key configurations and their impact:
●set type dynamic →This allows multiple peers to establish connections dynamically without needing predefined IP addresses.
●set ike-version 2 →Uses IKEv2, which is more efficient and supports features like EAP authentication and reduced rekeying overhead.
●set dpd on-idle →Dead Peer Detection (DPD) is triggered only when the tunnel is idle, reducing unnecessary keep-alive packets and improving resource utilization.
●set add-route enable →FortiGate automatically adds the route to the routing table when the tunnel is established, ensuring connectivity when needed.
●set proposal aes128-sha256 aes256-sha256 →Uses strong encryption and hashing algorithms, ensuring a secure connection.
●set keylife 28800 →Sets a longer key lifetime (8 hours), reducing the frequency of rekeying, which is beneficial for stable connections.
Because DPD is set to on-idle, the tunnel will not constantly send keep-alive messages but will still ensure connectivity when traffic is detected. This makes the configuration ideal for networks with regular but non-continuous traffic, balancing security and resource efficiency.



A company's users on an IPsec VPN between FortiGate A and B have experienced intermittent issues since implementing VXLAN. The administrator suspects that packets exceeding the 1500-byte default MTU are causing the problems.
In which situation would adjusting the interface’s maximum MTU value help resolve issues caused by protocols that add extra headers to IP packets?

  1. Adjust the MTU on interfaces only if FortiGate has the FortiGuard enterprise bundle, which allows MTU modification.
  2. Adjust the MTU on interfaces in all FortiGate devices that support the latest family of Fortinet SPUs: NP7, CP9 and SP5.
  3. Adjust the MTU on interfaces in controlled environments where all devices along the path allow MTU interface changes.
  4. Adjust the MTU on interfaces only in wired connections like PPPoE, optic fiber, and ethernet cable.

Answer(s): C

Explanation:

When using IPsec VPNs and VXLAN, additional headers are added to packets, which can exceed the default 1500-byte MTU. This can lead to fragmentation issues, dropped packets, or degraded performance.
To resolve this, the MTU (Maximum Transmission Unit) should be adjusted only if all devices in the network path support it. Otherwise, some devices may still drop or fragment packets, leading to continued issues.
Why adjusting MTU helps:
●VXLAN adds a 50-byte overhead to packets.
●IPsec adds additional encapsulation (ESP, GRE, etc.), increasing the packet size.
●If packets exceed the MTU, they may be fragmented or dropped, causing intermittent connectivity issues.
●Lowering the MTU on interfaces ensures packets stay within the supported size limit across all network devices.



Refer to the exhibit, which shows a command output.

FortiGate_A and FortiGate_B are members of an FGSP cluster in an enterprise network.
While testing the cluster using the ping command, the administrator monitors packet loss and found that the session output on FortiGate_B is as shown in the exhibit.
What could be the cause of this output on FortiGate_B?

  1. The session synchronization is encrypted.
  2. session-pickup-connectionless is set to disable on FortiGate_
  3. FortiGate_B is configured in passive mode.
  4. FortiGate_A and FortiGate_B have the same standalone-group-id value.

Answer(s): B

Explanation:

The Fortinet FGSP (FortiGate Session Life Support Protocol) cluster allows session synchronization between two FortiGate devices to provide seamless failover. However, ICMP (ping) is a connectionless protocol, and by default, FortiGate does not synchronize connectionless sessions unless explicitly enabled.
In the exhibit:
●The command get system session list | grep icmp on FortiGate_B returns no output, meaning that ICMP sessions are not being synchronized from FortiGate_A.
●If session-pickup-connectionless is disabled, FortiGate_B will not receive ICMP sessions, causing packet loss during failover.



Refer to the exhibit, which shows a partial troubleshooting command output.

An administrator is extensively using IPsec on FortiGate. Many tunnels show information similar to the output shown in the exhibit.
What can the administrator conclude?

  1. IPsec SAs cannot be offloaded.
  2. The two IPsec SAs, inbound and outbound, are copied to the NPU.
  3. Only the outbound IPsec SA is copied to the NPU.
  4. Only the inbound IPsec SA is copied to the NPU.

Answer(s): A

Explanation:

Based on the FortiGate Infrastructure 7.6 study guide and the Hardware Acceleration technical documentation, the diagnose vpn tunnel list command provides the status of IPsec tunnel offloading to the Network Processor (NPU).
In the provided exhibit, the specific value npu_flag=20 (which corresponds to 0x20 in hexadecimal) indicates that the IPsec Security Association (SA) cannot be offloaded to the NPU.
While the NPU may have visibility of the gateway IPs (npu_rgwy and npu_lgwy), the flag itself serves as a diagnostic indicator that the traffic must be processed by the system CPU rather than the hardware accelerator.
This lack of offloading typically occurs when the tunnel configuration uses a cipher (encryption algorithm) or an HMAC (authentication algorithm) that is not supported by the specific NPU model installed in the FortiGate. For example, if a tunnel is configured with a legacy or highly complex algorithm that the NP6 or NP7 chip is not designed to process in hardware, the FortiOS kernel handles the encryption and decryption, resulting in the npu_flag=20 status. Therefore, despite the presence of NPU-related fields, the specific flag value confirms that hardware acceleration is not active for these SAs.



Refer to the exhibit, which shows a corporate network and a new remote office network.

An administrator must integrate the new remote office network with the corporate enterprise network.
What must the administrator do to allow routing between the two networks?

  1. The administrator must implement BGP to inject the new remote office network into the corporate FortiGate device
  2. The administrator must configure a static route to the subnet 192.168.l.0/24 on the corporate FortiGate device.
  3. The administrator must configure virtual links on both FortiGate devices.
  4. The administrator must implement OSPF over IPsec on both FortiGate devices.

Answer(s): D

Explanation:

In this scenario, the corporate network and the new remote office network need to communicate over the Internet, which requires a secure and dynamic routing method. Since both networks are using OSPF (Open Shortest Path First) as the routing protocol, the best approach is to establish an OSPF over IPsec VPN to ensure secure and dynamic route propagation.
OSPF is already running on the corporate network, and extending it over an IPsec tunnel allows dynamic route exchange between the corporate FortiGate and the remote office FortiGate. IPsec provides encryption for traffic over the Internet, ensuring secure communication. OSPF over IPsec eliminates the need for manual static routes, allowing automatic route updates if networks change.
The new remote office's 192.168.1.0/24 subnet will be advertised dynamically to the corporate network without additional configuration.



Refer to the exhibit, which shows an enterprise network connected to an internet service provider.

The administrator must configure the BGP section of FortiGate A to give internet access to the enterprise network.
Which command must the administrator use to establish a connection with the internet service provider?

  1. config neighbor
  2. config redistribute bgp
  3. config router route-map
  4. config redistribute ospf

Answer(s): A

Explanation:

In BGP (Border Gateway Protocol), a neighbor (peer) configuration is required to establish a connection between two BGP routers. Since FortiGate A is connecting to the ISP (Autonomous System 10) from AS 30, the administrator must define the ISP's BGP router as a neighbor.
The config neighbor command is used to:
●Define the ISP's IP address as a BGP peer
●Specify the remote AS (AS 10 in this case)
●Allow BGP route exchanges between FortiGate A and the ISP



Share your comments for Fortinet FCSS_EFW_AD-7.6 exam with other users:

G
Guss
5/23/2023 12:28:00 PM

hi, could you please add the last update of ns0-527

R
Rond65
8/22/2023 4:39:00 PM

question #3 refers to vnet4 and vnet5. however, there is no vnet5 listed in the case study (testlet 2).

C
Cheers
12/13/2023 9:55:00 AM

sometimes it may be good some times it may be

S
Sumita Bose
7/21/2023 1:01:00 AM

qs 4 answer seems wrong- please check

A
Amit
9/7/2023 12:53:00 AM

very detailed explanation !

F
FisherGirl
5/16/2022 10:36:00 PM

the interactive nature of the test engine application makes the preparation process less boring.

C
Chiranthaka
9/20/2023 11:15:00 AM

very useful.

S
SK
7/15/2023 3:51:00 AM

complete question dump should be made available for practice.

G
Gamerrr420
5/25/2022 9:38:00 PM

i just passed my first exam. i got 2 exam dumps as part of the 50% sale. my second exam is under work. once i write that exam i report my result. but so far i am confident.

K
Kudu hgeur
9/21/2023 5:58:00 PM

nice create dewey stefen

A
Anorag
9/6/2023 9:24:00 AM

i just wrote this exam and it is still valid. the questions are exactly the same but there are about 4 or 5 questions that are answered incorrectly. so watch out for those. best of luck with your exam.

N
Nathan
1/10/2023 3:54:00 PM

passed my exam today. this is a good start to 2023.

1
1
10/28/2023 7:32:00 AM

great sharing

A
Anand
1/20/2024 10:36:00 AM

very helpful

K
Kumar
6/23/2023 1:07:00 PM

thanks.. very helpful

U
User random
11/15/2023 3:01:00 AM

i registered for 1z0-1047-23 but dumps qre available for 1z0-1047-22. help me with this...

K
kk
1/17/2024 3:00:00 PM

very helpful

R
Raj
7/24/2023 10:20:00 AM

please upload oracle 1z0-1110-22 exam pdf

B
Blessious Phiri
8/13/2023 11:58:00 AM

becoming interesting on the logical part of the cdbs and pdbs

L
LOL what a joke
9/10/2023 9:09:00 AM

some of the answers are incorrect, i would be wary of using this until an admin goes back and reviews all the answers

M
Muhammad Rawish Siddiqui
12/9/2023 7:40:00 AM

question # 267: federated operating model is also correct.

M
Mayar
9/22/2023 4:58:00 AM

its helpful alot.

S
Sandeep
7/25/2022 11:58:00 PM

the questiosn from this braindumps are same as in the real exam. my passing mark was 84%.

E
Eman Sawalha
6/10/2023 6:09:00 AM

it is an exam that measures your understanding of cloud computing resources provided by aws. these resources are aligned under 6 categories: storage, compute, database, infrastructure, pricing and network. with all of the services and typees of services under each category

M
Mars
11/16/2023 1:53:00 AM

good and very useful

R
ronaldo7
10/24/2023 5:34:00 AM

i cleared the az-104 exam by scoring 930/1000 on the exam. it was all possible due to this platform as it provides premium quality service. thank you!

P
Palash Ghosh
9/11/2023 8:30:00 AM

easy questions

N
Noor
10/2/2023 7:48:00 AM

could you please upload ad0-127 dumps

K
Kotesh
7/27/2023 2:30:00 AM

good content

B
Biswa
11/20/2023 9:07:00 AM

understanding about joins

J
Jimmy Lopez
8/25/2023 10:19:00 AM

please upload oracle cloud infrastructure 2023 foundations associate exam braindumps. thank you.

L
Lily
4/24/2023 10:50:00 PM

questions made studying easy and enjoyable, passed on the first try!

J
John
8/7/2023 12:12:00 AM

has anyone recently attended safe 6.0 exam? did you see any questions from here?

B
Big Dog
6/24/2023 4:47:00 PM

question 13 should be dhcp option 43, right?

AI Tutor 👋 I’m here to help!