Fortinet FCSS - Enterprise Firewall 7.6 Administrator FCSS_EFW_AD-7.6 Dumps in PDF

Free Fortinet FCSS_EFW_AD-7.6 Real Questions (page: 10)

What does the command set forward-domain <domain_ID> in a transparent VDOM interface do?

  1. It configures the interface to prioritize traffic based on the domain ID, enhancing quality of service for specified VLANs.
  2. It isolates traffic within a specific VLAN by assigning a broadcast domain to an interface based on the VLAN ID.
  3. It restricts the interface to managing traffic only from the specified VLAN, effectively segregating network traffic.
  4. It assigns a unique domain ID to the interface, allowing it to operate across multiple VLANs within the same VDOM.

Answer(s): B

Explanation:

In a transparent mode Virtual Domain (VDOM) configuration, FortiGate operates as a Layer 2 bridge rather than performing Layer 3 routing. The set forward-domain <domain_ID> command is used to control how traffic is forwarded between interfaces within the same transparent VDOM.
A forward-domain acts as a broadcast domain, meaning only interfaces with the same forward-domain ID can exchange traffic. This setting is commonly used to separate different VLANs or network segments within the transparent VDOM while still allowing FortiGate to apply security policies.



Refer to the exhibit, which shows a physical topology and a traffic log.

The administrator is checking on FortiAnalyzer traffic from the device with IP address 10.1.10.1, located behind the FortiGate ISFW device.
The firewall policy in on the ISFW device does not have UTM enabled and the administrator is surprised to see a log with the action Malware, as shown in the exhibit.
What are the two reasons FortiAnalyzer would display this log? (Choose two.)

  1. Security rating is enabled in ISFW.
  2. ISFW is in a Security Fabric environment.
  3. ISFW is not connected to FortiAnalyzer and must go through NGFW-1.
  4. The firewall policy in NGFW-1 has UTM enabled.

Answer(s): B,D

Explanation:

From the exhibit, ISFW is part of a Security Fabric environment with NGFW-1 as the Fabric Root. In this architecture, FortiGate devices share security intelligence, including logs and detected threats.
ISFW is in a Security Fabric environment:
●Security Fabric allows devices like ISFW to receive threat intelligence from NGFW-1, even if UTM is not enabled locally.
●If NGFW-1 detects malware from IP 10.1.10.1 to 89.238.73.97, this information can be propagated to ISFW and FortiAnalyzer.
The firewall policy in NGFW-1 has UTM enabled:
●Even though ISFW does not have UTM enabled, NGFW-1 (which sits between ISFW and the external network) does have UTM enabled and is scanning traffic.
●Since NGFW-1 detects malware in the session, it logs the event, which is then sent to FortiAnalyzer.



Refer to the exhibit, which contains a partial VPN configuration.

What can you conclude from this VPN IPsec phase 1 configuration?

  1. This configuration is the best for networks with regular traffic intervals, providing a balance between connectivity assurance and resource utilization.
  2. Peer IDs are unencrypted and exposed, creating a security risk.
  3. FortiGate will not add a route to its routing or forwarding information base when the dynamic tunnel is negotiated.
  4. A separate interface is created for each dial-up tunnel, which can be slower and more resource intensive, especially in large networks.

Answer(s): A

Explanation:

This IPsec Phase 1 configuration defines a dynamic VPN tunnel that can accept connections from multiple peers. The settings chosen here suggest a configuration optimized for networks with intermittent traffic patterns while ensuring resources are used efficiently.
Key configurations and their impact:
●set type dynamic →This allows multiple peers to establish connections dynamically without needing predefined IP addresses.
●set ike-version 2 →Uses IKEv2, which is more efficient and supports features like EAP authentication and reduced rekeying overhead.
●set dpd on-idle →Dead Peer Detection (DPD) is triggered only when the tunnel is idle, reducing unnecessary keep-alive packets and improving resource utilization.
●set add-route enable →FortiGate automatically adds the route to the routing table when the tunnel is established, ensuring connectivity when needed.
●set proposal aes128-sha256 aes256-sha256 →Uses strong encryption and hashing algorithms, ensuring a secure connection.
●set keylife 28800 →Sets a longer key lifetime (8 hours), reducing the frequency of rekeying, which is beneficial for stable connections.
Because DPD is set to on-idle, the tunnel will not constantly send keep-alive messages but will still ensure connectivity when traffic is detected. This makes the configuration ideal for networks with regular but non-continuous traffic, balancing security and resource efficiency.



A company's users on an IPsec VPN between FortiGate A and B have experienced intermittent issues since implementing VXLAN. The administrator suspects that packets exceeding the 1500-byte default MTU are causing the problems.
In which situation would adjusting the interface’s maximum MTU value help resolve issues caused by protocols that add extra headers to IP packets?

  1. Adjust the MTU on interfaces only if FortiGate has the FortiGuard enterprise bundle, which allows MTU modification.
  2. Adjust the MTU on interfaces in all FortiGate devices that support the latest family of Fortinet SPUs: NP7, CP9 and SP5.
  3. Adjust the MTU on interfaces in controlled environments where all devices along the path allow MTU interface changes.
  4. Adjust the MTU on interfaces only in wired connections like PPPoE, optic fiber, and ethernet cable.

Answer(s): C

Explanation:

When using IPsec VPNs and VXLAN, additional headers are added to packets, which can exceed the default 1500-byte MTU. This can lead to fragmentation issues, dropped packets, or degraded performance.
To resolve this, the MTU (Maximum Transmission Unit) should be adjusted only if all devices in the network path support it. Otherwise, some devices may still drop or fragment packets, leading to continued issues.
Why adjusting MTU helps:
●VXLAN adds a 50-byte overhead to packets.
●IPsec adds additional encapsulation (ESP, GRE, etc.), increasing the packet size.
●If packets exceed the MTU, they may be fragmented or dropped, causing intermittent connectivity issues.
●Lowering the MTU on interfaces ensures packets stay within the supported size limit across all network devices.



Refer to the exhibit, which shows a command output.

FortiGate_A and FortiGate_B are members of an FGSP cluster in an enterprise network.
While testing the cluster using the ping command, the administrator monitors packet loss and found that the session output on FortiGate_B is as shown in the exhibit.
What could be the cause of this output on FortiGate_B?

  1. The session synchronization is encrypted.
  2. session-pickup-connectionless is set to disable on FortiGate_
  3. FortiGate_B is configured in passive mode.
  4. FortiGate_A and FortiGate_B have the same standalone-group-id value.

Answer(s): B

Explanation:

The Fortinet FGSP (FortiGate Session Life Support Protocol) cluster allows session synchronization between two FortiGate devices to provide seamless failover. However, ICMP (ping) is a connectionless protocol, and by default, FortiGate does not synchronize connectionless sessions unless explicitly enabled.
In the exhibit:
●The command get system session list | grep icmp on FortiGate_B returns no output, meaning that ICMP sessions are not being synchronized from FortiGate_A.
●If session-pickup-connectionless is disabled, FortiGate_B will not receive ICMP sessions, causing packet loss during failover.



Refer to the exhibit, which shows a partial troubleshooting command output.

An administrator is extensively using IPsec on FortiGate. Many tunnels show information similar to the output shown in the exhibit.
What can the administrator conclude?

  1. IPsec SAs cannot be offloaded.
  2. The two IPsec SAs, inbound and outbound, are copied to the NPU.
  3. Only the outbound IPsec SA is copied to the NPU.
  4. Only the inbound IPsec SA is copied to the NPU.

Answer(s): A

Explanation:

Based on the FortiGate Infrastructure 7.6 study guide and the Hardware Acceleration technical documentation, the diagnose vpn tunnel list command provides the status of IPsec tunnel offloading to the Network Processor (NPU).
In the provided exhibit, the specific value npu_flag=20 (which corresponds to 0x20 in hexadecimal) indicates that the IPsec Security Association (SA) cannot be offloaded to the NPU.
While the NPU may have visibility of the gateway IPs (npu_rgwy and npu_lgwy), the flag itself serves as a diagnostic indicator that the traffic must be processed by the system CPU rather than the hardware accelerator.
This lack of offloading typically occurs when the tunnel configuration uses a cipher (encryption algorithm) or an HMAC (authentication algorithm) that is not supported by the specific NPU model installed in the FortiGate. For example, if a tunnel is configured with a legacy or highly complex algorithm that the NP6 or NP7 chip is not designed to process in hardware, the FortiOS kernel handles the encryption and decryption, resulting in the npu_flag=20 status. Therefore, despite the presence of NPU-related fields, the specific flag value confirms that hardware acceleration is not active for these SAs.



Refer to the exhibit, which shows a corporate network and a new remote office network.

An administrator must integrate the new remote office network with the corporate enterprise network.
What must the administrator do to allow routing between the two networks?

  1. The administrator must implement BGP to inject the new remote office network into the corporate FortiGate device
  2. The administrator must configure a static route to the subnet 192.168.l.0/24 on the corporate FortiGate device.
  3. The administrator must configure virtual links on both FortiGate devices.
  4. The administrator must implement OSPF over IPsec on both FortiGate devices.

Answer(s): D

Explanation:

In this scenario, the corporate network and the new remote office network need to communicate over the Internet, which requires a secure and dynamic routing method. Since both networks are using OSPF (Open Shortest Path First) as the routing protocol, the best approach is to establish an OSPF over IPsec VPN to ensure secure and dynamic route propagation.
OSPF is already running on the corporate network, and extending it over an IPsec tunnel allows dynamic route exchange between the corporate FortiGate and the remote office FortiGate. IPsec provides encryption for traffic over the Internet, ensuring secure communication. OSPF over IPsec eliminates the need for manual static routes, allowing automatic route updates if networks change.
The new remote office's 192.168.1.0/24 subnet will be advertised dynamically to the corporate network without additional configuration.



Refer to the exhibit, which shows an enterprise network connected to an internet service provider.

The administrator must configure the BGP section of FortiGate A to give internet access to the enterprise network.
Which command must the administrator use to establish a connection with the internet service provider?

  1. config neighbor
  2. config redistribute bgp
  3. config router route-map
  4. config redistribute ospf

Answer(s): A

Explanation:

In BGP (Border Gateway Protocol), a neighbor (peer) configuration is required to establish a connection between two BGP routers. Since FortiGate A is connecting to the ISP (Autonomous System 10) from AS 30, the administrator must define the ISP's BGP router as a neighbor.
The config neighbor command is used to:
●Define the ISP's IP address as a BGP peer
●Specify the remote AS (AS 10 in this case)
●Allow BGP route exchanges between FortiGate A and the ISP



Share your comments for Fortinet FCSS_EFW_AD-7.6 exam with other users:

M
Mihai
7/19/2023 12:03:00 PM

i need the dumps !

W
Wafa
11/13/2023 3:06:00 AM

very helpful

A
Alokit
7/3/2023 2:13:00 PM

good source

S
Show-Stopper
7/27/2022 11:19:00 PM

my 3rd test and passed on first try. hats off to this brain dumps site.

M
Michelle
6/23/2023 4:06:00 AM

please upload it

L
Lele
11/20/2023 11:55:00 AM

does anybody know if are these real exam questions?

G
Girish Jain
10/9/2023 12:01:00 PM

are these questions similar to actual questions in the exam? because they seem to be too easy

P
Phil
12/8/2022 11:16:00 PM

i have a lot of experience but what comes in the exam is totally different from the practical day to day tasks. so i thought i would rather rely on these brain dumps rather failing the exam.

B
BV
6/8/2023 4:35:00 AM

good questions

K
krishna
12/19/2023 2:05:00 AM

valied exam dumps. they were very helpful and i got a pretty good score. i am very grateful for this service and exam questions

P
Pie
9/3/2023 4:56:00 AM

will it help?

L
Lucio
10/6/2023 1:45:00 PM

very useful to verify knowledge before exam

A
Ajay
5/17/2023 4:54:00 AM

good stuffs

T
TestPD1
8/10/2023 12:19:00 PM

question 17 : responses arent b and c ?

N
Nhlanhla
12/13/2023 5:26:00 AM

just passed the exam on my first try using these dumps.

R
Rizwan
1/6/2024 2:18:00 AM

very helpful

Y
Yady
5/24/2023 10:40:00 PM

these questions look good.

K
Kettie
10/12/2023 1:18:00 AM

this is very helpful content

S
SB
7/21/2023 3:18:00 AM

please provide the dumps

D
David
8/2/2023 8:20:00 AM

it is amazing

U
User
8/3/2023 3:32:00 AM

quesion 178 about "a banking system that predicts whether a loan will be repaid is an example of the" the answer is classification. not regresion, you should fix it.

Q
quen
7/26/2023 10:39:00 AM

please upload apache spark dumps

E
Erineo
11/2/2023 5:34:00 PM

q14 is b&c to reduce you will switch off mail for every single alert and you will switch on daily digest to get a mail once per day, you might even skip the empty digest mail but i see this as a part of the daily digest adjustment

P
Paul
10/21/2023 8:25:00 AM

i think it is good question

U
Unknown
8/15/2023 5:09:00 AM

good for students who wish to give certification.

C
Ch
11/20/2023 10:56:00 PM

is there a google drive link to the images? the links in questions are not working.

J
Joey
5/16/2023 5:25:00 AM

very promising, looks great, so much wow!

A
alaska
10/24/2023 5:48:00 AM

i scored 87% on the az-204 exam. thanks! i always trust

N
nnn
7/9/2023 11:09:00 PM

good need more

U
User-sfdc
12/29/2023 7:21:00 AM

sample questions seems good

T
Tamer dam
8/4/2023 10:21:00 AM

huawei is ok

Y
YK
12/11/2023 1:10:00 AM

good one nice

D
de
8/28/2023 2:38:00 AM

please continue

D
DMZ
6/25/2023 11:56:00 PM

this exam dumps just did the job. i donot want to ruffle your feathers but your exam dumps and mock test engine is amazing.

AI Tutor 👋 I’m here to help!