An administrator has a NetApp AFF cluster with two SVMs serving LUNs. SnapMirror active sync is configured, and a disaster recovery test is planned over the weekend. Which NetApp ONTAP command will show the status of this test?
Answer(s): A
To check the status of a SnapMirror active sync disaster recovery test on a NetApp ONTAP cluster, you would use the command snapmirror failover show. This command provides the necessary details about the failover status, helping administrators verify if the disaster recovery test is proceeding as expected. It displays the status of the failover groups and their readiness, which is essential for confirming the effectiveness of the disaster recovery setup. For more detailed information on SnapMirror commands and their usage, refer to:NetApp Documentation - SnapMirror Commands(NetApp Community)(NetApp Community).
What configuration must be applied for NVMe/FC?
Answer(s): D
When configuring NVMe/FC (NVMe over Fibre Channel), it is necessary to enable N_Port ID Virtualization (NPIV) on all fabric switches. NPIV allows multiple Fibre Channel initiators to share a single physical Fibre Channel port, which is crucial for NVMe/FC environments where efficient utilization of available ports is needed.NPIV support enables the creation of virtual ports, which can significantly optimize the configuration and management of Fibre Channel fabrics, thus supporting NVMe/FC operations.For further details, you can refer to:NetApp Community - NVMe/FC Configuration(NetApp Community).NetApp Documentation - NVMe Overview(NetApp).
A storage administrator has just completed an ISCSI implementation in a customer environment running VMware and needs to validate that the entire network path supports jumbo frames.Which action should be taken?
To validate that the entire network path supports jumbo frames after an iSCSI implementation, you should perform a ping test from the host with fragmentation. This involves using the ping command with specific options to test jumbo frame support:ping -M do -s 8972 <target_IP>In this command:-M do ensures the packets are not fragmented.-s 8972 sets the packet size to 8972 bytes (9000 bytes MTU minus 28 bytes for the ICMP header). By confirming that the large packets are successfully transmitted without fragmentation, you can validate that the network path, including switches and adapters, supports jumbo frames.For more details, you can check:NetApp Documentation - iSCSI Configuration and Best Practices(NetApp)(NetApp).
An administrator installs a new NetApp ONTAP system in a customer's SAN environment. The customer wants to confirm that ALUA correctly changes the path states between Active/Optimized and Active/Nonoptimized.Which event causes ALUA to change the path states?
ALUA (Asymmetric Logical Unit Access) is a protocol used in SAN environments to manage paths between a host and its storage. It enables the host to recognize and manage paths to the LUNs more efficiently by designating paths as either "Active/Optimized" or "Active/Nonoptimized". A significant event, such as shutting down all FC LIFs on the HA partner node, will trigger ALUA to change the path states. This action effectively causes the storage paths to transition from the HA partner node to the local node, switching the path states from Active/Nonoptimized to Active/Optimized on the paths that remain active.For more information, you can refer to:NetApp Community Discussion on ALUANetApp Documentation on ALUA
An engineer Is implementing a data migration scenario for a customer who has multiple FC LUNs across multiple third-party SAN arrays. The engineer wants to use Foreign LUN Import (FLI) for the migration.What is a requirement on the destination NetApp ONTAP cluster for FLI?
When using Foreign LUN Import (FLI) for migrating LUNs from third-party SAN arrays to a NetApp ONTAP system, one of the requirements is to have at least one Fibre Channel (FC) port configured in target mode on the destination NetApp ONTAP cluster. This configuration is necessary to facilitate the migration process as the target mode port will accept and manage incoming data from the source SAN arrays.For additional details, refer to:NetApp Documentation on FLI
Share your comments for Network Appliance NS0-521 exam with other users:
question: 78 the right answer i think is d not a
very helpful
i am writing this exam tomorrow and have dumps
can i have the icdl excel exam
please upload it
hye when will post again the past year question for this h13-311_v3 part since i have to for my test tommorow…thank you very much
on question 22, option b-once per session is also valid.
this website is very helpful
its my first time exam
correct answers are device configuration-enable the automatic installation of webview2 runtime. & policy management- prevent users from submitting feedback.
is this dump still valid? today is 9-july-2023
i need this exam.. please upload these are really helpful
please upload the oracle 1z0-1059-22 dumps
very good questions
nice, first step to exams
is this valid for chfiv9 as well... as i am reker 3rd time...
great exam for people taking 220-1101
this is very helpfull for me
just started preparing for the exam
these are the type of questions i need.
does this actually work? are they the exam questions and answers word for word?
thanks for providing these questions
interesting
these dumps are pretty good.
good questions
dbua is used for upgrading oracle database
i am thrilled to say that i passed my amazon web services mls-c01 exam, thanks to study materials. they were comprehensive and well-structured, making my preparation efficient.
please upload latest ibm ace c1000-056 dumps
if only explanations were provided...
yes .. i need the dump if you can help me
good morning, could you please upload this exam again?
hi please upload sre foundation and practitioner exam questions
the exam is listed as 80 questions with a pass mark of 70%, how is your 50 questions related?
all questions are so important and covers all ccna modules
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your NS0-521, please sign in or create a free account.