Huawei HCIP-Datacom-Advanced Routing & Switching Technology H12-831 Dumps in PDF

Free Huawei H12-831 Real Questions (page: 8)

What is the purpose of configuring LSP fragmentation for IS-IS equipment?

  1. Make the device unable to establish IS-IS neighbors
  2. Allow the device to support more IS-IS routing entries
  3. Make the device unable to learn IS-IS routing information
  4. No practical purpose

Answer(s): B



Which of the following statements about IS-IS (IPv6) is correct? (Choose three.)

  1. To support the processing and calculation of IPv6 routing, IS-IS added NLPID to 129 TLV
  2. IS-IS working at the data link layer only needs to add a new TLV to support Pv6
  3. To support the processing and calculation of IPv6 routes, IS-IS has added TLV232236
  4. By default, IS-IS enables the multi-topology feature

Answer(s): A,B,C



Regarding the cause of the dual-master failure of the VRRP backup group, which of the following is the most unlikely?

  1. The link that transmits the VRRP notification message is faulty
  2. The low-priority VRRP backup group discards the received VRRP notification packets as illegal packets
  3. The VRRP backup group IDs on both ends are different
  4. Master device sends 1 notification message per second

Answer(s): D



Which of the following is not part of the preliminary preparations for the cutover plan?

  1. On-site defense
  2. Cutover target
  3. Introduction to the current network
  4. Risk assessment

Answer(s): A



During the process of viewing the debug output through the SSH terminal, a lot of information pops up.
Which of the following operations can make the Moni tor terminal no longer pop up the debug message?

  1. Exit the current Monitor interface, log in to the device again using SSH to open the new Monitor interface
  2. Open the notepad, enter undo debugging all, copy the command line, and paste it into the Monitor interface
  3. Open the notepad, enter undo terminal monitor, copy the command line, and paste it into the monitor interface
  4. Open the notepad, enter undo terminal debugging, copy the command line, and paste it into the Monitor interface

Answer(s): D



R1 executes the operation ping -a 10.1.1.1 10.5.16.2, what does this command mean?

  1. The source IP address of the ping packet is any directly connected port address of R1
  2. The source IFP address of the ping packet is the outgoing interface address of the optimal IP route that R1
    points to 10.5.16.2, and is not 10.1.1.1
  3. The source IP address of the ping packet is 10.1.1.1
  4. The destination IP address of the ping packet is 10.1.1.1 and 10.5.16.2

Answer(s): C



Regarding the role of ping and tracert, which of the following statements is correct?

  1. Ping detects the two-way reachability between the correct end and the one-way icmp echo request packet
  2. Tracert must be able to trace every hop IP address from source to destination
  3. Ping verifies the reachability from the local end to the opposite end, it does not mean that the opposite end is reachable from the local end
  4. Tracert has the same function as ping, but the name is different

Answer(s): C



In the intra-domain MPLS VPN network, when the data packet enters the public network and is forwarded, it will be encapsulated with two layers of MPLS labels. Regarding the description of the two layers of labels, which of the following options is wrong?

  1. The outer label of MPLS VPN is allocated by the LDP protocol or statically, and the inner label is allocated by the MP-BGP neighbor at the correct end.
  2. The outer label of MPLS VPNE is called the private network label, and the inner label is called the public network label.
  3. By default, the outer label is singled out before the packet is forwarded to the last hop device
  4. The outer label is used to correctly send the data packet to the corresponding VPN on the PE device

Answer(s): B



Share your comments for Huawei H12-831 exam with other users:

A
Anonymous User
4/16/2026 10:54:18 AM

Question 1:

  • Correct answer: E — date = sys.argv[1]
  • Why this is correct:
- When a Databricks Job passes parameters to a notebook, those parameters are supplied to the notebook's Python process as command-line arguments. The first argument after the script name is sys.argv[1], so date = sys.argv[1] captures the passed date value directly.
  • How it compares to other options:
- date = spark.conf.get("date") reads from Spark config, not from job parameters. - input() waits for user input at runtime, which isn’t how job parameters are provided. - date = dbutils.notebooks.getParam("date") would work if the notebook were invoked via dbutils.notebook.run with parameters, not

A
Anonymous User
4/15/2026 4:42:07 AM

Question 528:

  • Correct answer: NSG flow logs for NSG1 (Option B)

  • Why:
- Traffic Analytics uses NSG flow logs to analyze traffic patterns. You must have NSG flow logs enabled for the NSGs you want to monitor. - An Azure Log Analytics workspace is also required to store and query the traffic data. - Network Watcher must be available in the subscription for traffic analytics to function.
  • What to configure (brief steps):
- Ensure Network Watcher is enabled in the East US region (for the subscription/region). - Enable NSG flow logs on NSG1. - Ensure a Log Analytics workspace exists and is accessible (read/write) so Traffic Analytics can store and query logs.
  • Why other options aren’t correct:
- “Diagnostic settings for VM1” or “Diagnostic settings for NSG1” alone don’t guarantee flow logs are captured and sent to Log Analytics, which Traffic Analytics relies on. - “Insights for VM1” is not how Traffic Analytics collects traffic data.

A
Anonymous User
4/15/2026 2:43:53 AM

Question 23:
The correct answer is Domain admin (option B), not Fabric admin.

  • Domain admin provides domain-level management: create domains/subdomains and assign workspaces within those domains, which matches the tasks while following least privilege.
  • Fabric admin is global-level access and is more privileges than needed for this scenario (it would grant broader control across the Fabric environment).

A
Anonymous User
4/14/2026 12:31:34 PM

Question 2:
For question 2, the key concept is the Longest Prefix Match. Routers pick the route whose subnet mask is the most specific (largest prefix length) that still matches the destination IP.
From the options:

  • A) 10.10.10.0/28 ? 10.10.10.0–10.10.10.15
  • B) 10.10.13.0/25 ? 10.10.13.0–10.10.13.127
  • C) 10.10.13.144/28 ? 10.10.13.144–10.10.13.159
  • D) 10.10.13.208/29 ? 10.10.13.208–10.10.13.215

The destination Host A’s IP must fall within 10.10.13.208–10.10.13.215 for the /29 to be the best match. Since /29 is the longest prefix among the matching options, Router1 will use 10.10.13.208/29.
Thus, the correct answer is D.

S
srameh
4/14/2026 10:09:29 AM

Question 3:

  • Correct answer: Phase 4, Post Accreditation

  • Explanation:
- In DITSCAP, the four phases are: - Phase 1: Definition (concept and requirements) - Phase 2: Verification (design and testing) - Phase 3: Validation (fielding and evaluation) - Phase 4: Post Accreditation (ongoing operations and lifecycle management) - The description—continuing operation of an accredited IT system and addressing changing threats throughout its life cycle—fits the Post Accreditation phase, which covers operations, maintenance, monitoring, and reauthorization as threats and environment evolve.

O
onibokun10
4/13/2026 7:50:14 PM

Question 129:
Correct answer: CNAME

  • A CNAME record creates an alias for a domain, so newapplication.comptia.org will resolve to whatever IP address www.comptia.org resolves to. This ensures both names point to the same resource without duplicating the IP.
  • Why not the others:
- SOA defines authoritative information for a zone. - MX specifies mail exchange servers. - NS designates name servers for a zone.
  • Notes: The alias name (newapplication.comptia.org) should not have other records if you use a CNAME for it, and CNAMEs aren’t used for the zone apex (root) domain. This scenario uses a subdomain, so a CNAME is appropriate.

A
Anonymous User
4/13/2026 6:29:58 PM

Question 1:

  • Correct answer: C

  • Why this is best:
- Uses OS Login with IAM, so SSH access is granted via Google accounts rather than distributing per-user SSH keys. - Granting the compute.osAdminLogin role to a Google group gives admin access to all team members in a centralized, auditable way. - Access is auditable: Cloud Audit Logs show who accessed which VM, satisfying the security requirement to determine who accessed a given instance.
  • How it works:
- Enable OS Login on the project/instances (enable-oslogin metadata). - Add the team’s

A
Anonymous User
4/13/2026 1:00:51 PM

Question 2:

  • Answer: D. Azure Advisor

  • Why: To view security-related recommendations for resources in the Compute and Apps area (including App Service Web Apps and Functions), you use Azure Advisor. Advisor surfaces personalized best-practice recommendations across resources, including security, and shows which resources are affected and the severity.

  • Why not the others:
- Azure Log Analytics is for ad-hoc querying of telemetry, not for viewing security recommendations. - Azure Event Hubs is for streaming telemetry data, not for security recommendations.
  • Quick tip: In the portal, navigate to Azure Advisor and check the Security recommendations for App Services to see actionable items and affe

D
Don
4/11/2026 5:36:42 AM

Recommend using AI for Solutions rather the Answer(s) submitted here

M
Mogae Malapela
4/8/2026 6:37:56 AM

This is very interesting

A
Anon
4/6/2026 5:22:54 PM

Are these the same questions you have to pay for in ExamTopics?

L
LRK
3/22/2026 2:38:08 PM

For Question 7 - while the answer description indicates the correct answer, the option no. mentioned is incorrect. Nice and Comprehensive. Thankyou

R
Rian
3/19/2026 9:12:10 AM

This is very good and accurate. Explanation is very helpful even thou some are not 100% right but good enough to pass.

G
Gerrard
3/18/2026 6:58:37 AM

The DP-900 exam can be tricky if you aren't familiar with Microsoft’s specific cloud terminology. I used the practice questions from free-braindumps.com and found them incredibly helpful. The site breaks down core data concepts and Azure services in a way that actually mirrors the real test. As a resutl I passed my exam.

V
Vineet Kumar
3/6/2026 5:26:16 AM

interesting

J
Joe
1/20/2026 8:25:24 AM

Passed this exam 2 days ago. These questions are in the exam. You are safe to use them.

N
NJ
12/24/2025 10:39:07 AM

Helpful to test your preparedness before giving exam

A
Ashwini
12/17/2025 8:24:45 AM

Really helped

J
Jagadesh
12/16/2025 9:57:10 AM

Good explanation

S
shobha
11/29/2025 2:19:59 AM

very helpful

P
Pandithurai
11/12/2025 12:16:21 PM

Question 1, Ans is - Developer,Standard,Professional Direct and Premier

E
Einstein
11/8/2025 4:13:37 AM

Passed this exam in first appointment. Great resource and valid exam dump.

D
David
10/31/2025 4:06:16 PM

Today I wrote this exam and passed, i totally relay on this practice exam. The questions were very tough, these questions are valid and I encounter the same.

T
Thor
10/21/2025 5:16:29 AM

Anyone used this dump recently?

V
Vladimir
9/25/2025 9:11:14 AM

173 question is A not D

K
khaos
9/21/2025 7:07:26 AM

nice questions

K
Katiso Lehasa
9/15/2025 11:21:52 PM

Thanks for the practice questions they helped me a lot.

E
Einstein
9/2/2025 7:42:00 PM

Passed this exam today. All questions are valid and this is not something you can find in ChatGPT.

V
vito
8/22/2025 4:16:51 AM

i need to pass exam for VMware 2V0-11.25

M
Matt
7/31/2025 11:44:40 PM

Great questions.

O
OLERATO
7/1/2025 5:44:14 AM

great dumps to practice for the exam

A
Adekunle willaims
6/9/2025 7:37:29 AM

How reliable and relevant are these questions?? also i can see the last update here was January and definitely new questions would have emerged.

A
Alex
5/24/2025 12:54:15 AM

Can I trust to this source?

S
SPriyak
3/17/2025 11:08:37 AM

can you please provide the CBDA latest test preparation

AI Tutor 👋 I’m here to help!