FILL BLANKBGP uses a (an) _________ message to withdraw routes. (Enter all letters in lower case.)
Answer(s): A
BGP (Border Gateway Protocol) uses the update message to advertise new routes and withdraw existing routes. When a route is no longer available, BGP sends an update message with the withdrawn routes field, indicating that the route should be removed from the BGP table of the receiving router.Update message is used for both advertising and withdrawing routes in BGP.
Which of the following statements regarding the summary automatic command and BGP route summarization is false?
The summary automatic command in BGP is used to enable automatic summarization, but manual summarization takes precedence over automatic summarization. If you configure manual summarization, it will override the automatic summarization.Automatic summarization does not override manual summarization; it works only when manual summarization is not configured.
When two BGP peers support different Hold Time, they will negotiate to support the shortest Hold Time interval they can support.
In BGP (Border Gateway Protocol), the Hold Time is the maximum time a router waits before declaring a neighbor as dead if no messages (such as Keepalive or Update) are received from the neighbor. The Hold Time is negotiated during the initial BGP session establishment between two peers.If two BGP peers have different Hold Times, they will negotiate and use the shorter of the two Hold Times as the effective Hold Time for that BGP session. This ensures both peers are synchronized in terms of how long they will wait before considering the neighbor down.
In the VRP, by default, the routes imported by BGP will be automatically summarized.
Answer(s): B
In VRP (Virtual Routing Platform), BGP (Border Gateway Protocol) does not automatically summarize routes by default. BGP requires manual configuration for route summarization, meaning that automatic route summarization is disabled by default.If you want to summarize routes in BGP, you must use specific commands like aggregate-address to configure manual summarization.
Which of the following statements regarding Local-Preference in BGP is true?
Answer(s): C
By default, Local-Preference is set to 100 for all BGP routes if no other value is configured. This value can be adjusted based on network requirements to influence the outbound traffic routing.
Which of the following scenarios is not suitable for deploying interface PBR?
Answer(s): D
In this scenario, Policy-Based Routing is not ideal because it is more appropriate to use routing protocols or policy routing at a higher level, like static routing or dynamic routing (e.g., using BGP or OSPF), which allows traffic from different internal network segments to use specific outbound ISP interfaces. PBR is typically not the most scalable or efficient method for this type of scenario, especially when there are multiple outbound paths and policies for each segment.
Which of the following statements regarding characteristics of IP prefixes is false?
An IP prefix filter is used for routing decisions, not for filtering data packets. It filters routing information in routing tables, not the actual data traffic that is sent between devices. Data packet filtering is typically done using ACLs or firewall rules, not IP prefix filters.
A route-policy can have multiple nodes, and each node can have multiple if-match and apply clauses. Which of the following statements are false? (Choose all that apply.)
Answer(s): B,D
The operator between nodes is AND.The operator between nodes in a route-policy is typically OR, not AND. This means that if any node matches, the corresponding apply action will be executed, even if the other nodes do not match.The operator between if-match clauses under a node is OR.The operator between if-match clauses under the same node is AND, not OR. All conditions in the same node must be true for the apply action to be triggered.
Share your comments for Huawei H12-821 exam with other users:
i think the answer to question 42 is b not c
thanks for the dump
fantastic assessments
i find the xengine test engine simulator to be more fun than reading from pdf.
nice document
thank you for making the questions and answers intractive and selectable.
answers are correct?
can i belive this dump
great site to practice for sitecore exam
good for students
nice practice dumps
nokia 4a0-114 dumps
great content and wonderful to have the answers with explanation
for question #118, the answer is option c. the screen shot is showing the drop down, but the answer is marked incorrectly please update . thanks for sharing such nice questions.
the correct answer for the question 29 is d.
question no 22: correct answers: bc, 1 per session 1 per page 1 per component always
these are pretty useful
awesome
yes please upload
great job whoever put this together, for the greater good! thanks!
just started to view all questions for the exam
helpful material
hope for the best
will post exam has finished
really correct and good analyze!
excellent thanks a lot
will post once pass the cka exam
good content
q:32 answer has to be option c
nice questions
i really like the support team in this website. they are fast in communication and very helpful.
a good contemporary exam review
q23, its an array, isnt it? starts with [ and end with ]. its an array of objects, not object.
cool very helpfull
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your H12-821, please sign in or create a free account.