FILL BLANKBGP uses a (an) _________ message to withdraw routes. (Enter all letters in lower case.)
Answer(s): A
BGP (Border Gateway Protocol) uses the update message to advertise new routes and withdraw existing routes. When a route is no longer available, BGP sends an update message with the withdrawn routes field, indicating that the route should be removed from the BGP table of the receiving router.Update message is used for both advertising and withdrawing routes in BGP.
Which of the following statements regarding the summary automatic command and BGP route summarization is false?
The summary automatic command in BGP is used to enable automatic summarization, but manual summarization takes precedence over automatic summarization. If you configure manual summarization, it will override the automatic summarization.Automatic summarization does not override manual summarization; it works only when manual summarization is not configured.
When two BGP peers support different Hold Time, they will negotiate to support the shortest Hold Time interval they can support.
In BGP (Border Gateway Protocol), the Hold Time is the maximum time a router waits before declaring a neighbor as dead if no messages (such as Keepalive or Update) are received from the neighbor. The Hold Time is negotiated during the initial BGP session establishment between two peers.If two BGP peers have different Hold Times, they will negotiate and use the shorter of the two Hold Times as the effective Hold Time for that BGP session. This ensures both peers are synchronized in terms of how long they will wait before considering the neighbor down.
In the VRP, by default, the routes imported by BGP will be automatically summarized.
Answer(s): B
In VRP (Virtual Routing Platform), BGP (Border Gateway Protocol) does not automatically summarize routes by default. BGP requires manual configuration for route summarization, meaning that automatic route summarization is disabled by default.If you want to summarize routes in BGP, you must use specific commands like aggregate-address to configure manual summarization.
Which of the following statements regarding Local-Preference in BGP is true?
Answer(s): C
By default, Local-Preference is set to 100 for all BGP routes if no other value is configured. This value can be adjusted based on network requirements to influence the outbound traffic routing.
Which of the following scenarios is not suitable for deploying interface PBR?
Answer(s): D
In this scenario, Policy-Based Routing is not ideal because it is more appropriate to use routing protocols or policy routing at a higher level, like static routing or dynamic routing (e.g., using BGP or OSPF), which allows traffic from different internal network segments to use specific outbound ISP interfaces. PBR is typically not the most scalable or efficient method for this type of scenario, especially when there are multiple outbound paths and policies for each segment.
Which of the following statements regarding characteristics of IP prefixes is false?
An IP prefix filter is used for routing decisions, not for filtering data packets. It filters routing information in routing tables, not the actual data traffic that is sent between devices. Data packet filtering is typically done using ACLs or firewall rules, not IP prefix filters.
A route-policy can have multiple nodes, and each node can have multiple if-match and apply clauses. Which of the following statements are false? (Choose all that apply.)
Answer(s): B,D
The operator between nodes is AND.The operator between nodes in a route-policy is typically OR, not AND. This means that if any node matches, the corresponding apply action will be executed, even if the other nodes do not match.The operator between if-match clauses under a node is OR.The operator between if-match clauses under the same node is AND, not OR. All conditions in the same node must be true for the apply action to be triggered.
Share your comments for Huawei H12-821 exam with other users:
good question
really nice
please i need dumps for isc2 cybersecuity
ans is coldline i think
very helpful
can you please provide dumps so that it helps me more
thank you for providing me with the updated question and answers. this version has all the questions from the exam. i just saw them in my exam this morning. i passed my exam today.
how i can see exam questions?
can you please upload please?
question 75: option c is correct answer
please add this exam
please upoad
has anyone recently attended safe 6.0 certification? is it the samq question from here.
expository experience
52 should be b&c. controller failure has nothing to do with this type of issue. degraded state tells us its a raid issue, and if the os is missing then the bootable device isnt found. the only other consideration could be data loss but thats somewhat broad whereas b&c show understanding of the specific issues the question is asking about.
great help!!!
very useful tools
looks a good platform to prepare az-104
want to pass the exam
good resource
question 11 : d
only the free dumps will be enough for pass, or have to purchase the premium one. please suggest.
good questions. thanks.
good for practice.
great case study
the questions in this exam dumps is valid. i passed my test last monday. i only whish they had their pricing in inr instead of usd. but it is still worth it.
q40 the answer is not d, why are you giving incorrect answers? snapshot consolidation is used to merge the snapshot delta disk files to the vm base disk
thanks, very relevant
wrong answer. it is true not false.
please i need the mo-100 questions
very good use full
very valid questions
will these question help me to clear pl-300 exam?
please provide me with these dumps questions. thanks
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your H12-821, please sign in or create a free account.