GAQM Linux Certified Professional (LCP) Powered by LPI LCP-001 Dumps in PDF

Free GAQM LCP-001 Real Questions (page: 1)

You suspect that a new ethernet card might be conflicting with another device.
Which file should you check within the /proc tree to learn which IRQs are being used by which kernel drives?

  1. interrupts

Answer(s): A

Explanation:

/proc/interrupts



How many SCSI ids for peripherals can SCSI-1 support?

  1. 5
  2. 6
  3. 7
  4. 8

Answer(s): C

Explanation:

SCSI-1 support total 7 peripherals. There are several different types of SCSI devices. The original SCSI specification is commonly referred to as SCSI-1. The newer specification, SCSI-2, offers increased speed and performance, as well as new commands. Fast SCSI increases throughput to more than 10MB per second. Fast-Wide SCSI provides a wider data path and throughput of up to 40MB per second and up to 15 devices. There there are Ultra-SCSI and Ultra-Wide-SCSI



You need to install a fax server.
Which type of fax/modem should you install to insure Linux compatibility?

  1. External Serial Fax/modem
  2. External USB Fax/modem
  3. Internal ISA Fax/modem
  4. Internal PCI Fax/modem

Answer(s): A



You are running Linux 2.0.36 and you need to add a USB mouse to your system.
Which of the following statements is true?

  1. You need to rebuild the kernel.
  2. You need to upgrade the kernel.
  3. You need to load the USB modules for your existing modular kernel.
  4. USB support is no available in Linux.

Answer(s): B



You have just upgraded your PC to a 60 gigabyte IDE drive.
While partitioning the drive, you notice that only 32 gigabytes are available.
Which of the following will most likely allow you to use the entire drive?

  1. Create two smaller partitions of 30 gigabytes each.
  2. Set the PC BIOS to use LBA mode.
  3. Create a partition that resides entirely below the first 1024 cylinders.
  4. Use GRUB or the latest version of LILO as a bootloader.
  5. Upgrade the PC BIOS to the latest version available.

Answer(s): E



The lspci command can display information about devices except the following:

  1. Card bus speed (e.g. 66Mhz)
  2. Card IRQ settings
  3. Card vendor identification
  4. Card AGP rate (e.g. 1x, 2x, 4x)
  5. Card Ethernet MAC address

Answer(s): E

Explanation:

lspci is a utility for displaying information about all PCI buses in the system and all devices connected to them. To display the MAC address of Ethernet, we use the ifconfig command.



If Linux detects an ACPI BIOS on bootup, what does it automatically deactivate?

  1. PnP
  2. PCI
  3. ATA
  4. APM

Answer(s): D



What command would help you identify the I/O address range being used by the network card?

  1. cat/proc/modules
  2. cat/proc/devices
  3. cat/proc/meminfo
  4. cat/io/dma
  5. cat/proc/ioports

Answer(s): E



Share your comments for GAQM LCP-001 exam with other users:

J
Jefi
9/4/2023 8:15:00 AM

please upload the practice questions

T
Thembelani
5/30/2023 2:45:00 AM

need this dumps

A
Abduraimov
4/19/2023 12:43:00 AM

preparing for this exam is overwhelming. you cannot pass without the help of these exam dumps.

P
Puneeth
10/5/2023 2:06:00 AM

new to this site but i feel it is good

A
Ashok Kumar
1/2/2024 6:53:00 AM

the correct answer to q8 is b. explanation since the mule app has a dependency, it is necessary to include project modules and dependencies to make sure the app will run successfully on the runtime on any other machine. source code of the component that the mule app is dependent of does not need to be included in the exported jar file, because the source code is not being used while executing an app. compiled code is being used instead.

M
Merry
7/30/2023 6:57:00 AM

good questions

V
VoiceofMidnight
12/17/2023 4:07:00 PM

Delayed the exam until December 29th.

U
Umar Ali
8/29/2023 2:59:00 PM

A and D are True

V
vel
8/28/2023 9:17:09 AM

good one with explanation

G
Gurdeep
1/18/2024 4:00:15 PM

This is one of the most useful study guides I have ever used.

AI Tutor 👋 I’m here to help!