Exhibit.Refer to the exhibit, which provides information on BGP neighbors.Which can you conclude from this command output?
Answer(s): C
The BGP state is "Idle", indicating that BGP is attempting to establish a TCP connection with the peer. This is the first state in the BGP finite state machine, and it means that no TCP connection has been established yet. If the TCP connection fails, the BGP state will reset to either active or idle, depending on the configuration.
You can find more information about BGP states and troubleshooting in the following Fortinet Enterprise Firewall 7.2 documents:Troubleshooting BGPHow BGP works
Exhibit.Refer to the exhibit, which contains the partial ADVPN configuration of a spoke.Which two parameters must you configure on the corresponding single hub? (Choose two.)
Answer(s): A,B
For an ADVPN spoke configuration shown, the corresponding hub must have auto-discovery-sender enabled to send shortcut advertisement messages to the spokes. Also, the hub would need to have auto-discovery-forwarder enabled if it is to forward on those shortcut advertisements to other spokes. This allows the hub to inform all spokes about the best path to reach each other. The ike- version does not need to be reconfigured on the hub if it's already set to version 2 and auto- discovery-receiver is not necessary on the hub because it's the one sending the advertisements, not receiving.
FortiOS Handbook - ADVPN
Which FortiGate in a Security I auric sends togs to FortiAnalyzer?
Answer(s): B
Option B is correct because each FortiGate in the Security Fabric can send logs to FortiAnalyzer for centralized logging and analysis12. This allows you to monitor and manage the entire Security Fabric from a single console and view aggregated reports and dashboards.Option A is incorrect because the root FortiGate is not the only device that can send logs to FortiAnalyzer. The root FortiGate is the device that initiates the Security Fabric and acts as the central point of contact for other FortiGate devices3. However, it does not have to be the only log source for FortiAnalyzer.Option C is incorrect because the FortiGate devices performing NAT or UTM are not the only devices that can send logs to FortiAnalyzer. These devices can perform additional security functions on the traffic that passes through them, such as firewall, antivirus, web filtering, etc4. However, they are not the only devices that generate logs in the Security Fabric.Option D is incorrect because the last FortiGate that handled a session in the Security Fabric is not the only device that can send logs to FortiAnalyzer. The last FortiGate is the device that terminates the session and applies the final security policy5. However, it does not have to be the only device that reports the session information to FortiAnalyzer.
=1: Security Fabric - Fortinet Documentation12: FortiAnalyzer Demo63: Security Fabric topology4: Security Fabric UTM features5: Security Fabric session handling
Which configuration can be used to reduce the number of BGP sessions in on IBGP network?
To reduce the number of BGP sessions in an IBGP network, you can use a route reflector, which acts as a focal point for IBGP sessions and readvertises the prefixes to all other peers. To configure a route reflector, you need to enable the route-reflector-client option on the neighbor-group settings of the hub device. This will make the hub device act as a route reflector server and the other devices as route reflector clients. Reference := Route exchange | FortiGate / FortiOS 7.2.0 - Fortinet Documentation
Exhibit.Refer to the exhibit, which contains an active-active toad balancing scenario.During the traffic flow the primary FortiGate forwards the SYN packet to the secondary FortiGate.What is the destination MAC address or addresses when packets are forwarded from the primary FortiGate to the secondary FortiGate?
Answer(s): A
In an active-active load balancing scenario, when the primary FortiGate forwards the SYN packet to the secondary FortiGate, the destination MAC address would be the secondary's physical MAC on port1, as the packet is being sent over the network and the physical MAC is used for layer 2 transmissions.
Share your comments for Fortinet NSE7_EFW-7.2 exam with other users:
helpful material
hope for the best
will post exam has finished
really correct and good analyze!
excellent thanks a lot
will post once pass the cka exam
good content
q:32 answer has to be option c
nice questions
i really like the support team in this website. they are fast in communication and very helpful.
a good contemporary exam review
q23, its an array, isnt it? starts with [ and end with ]. its an array of objects, not object.
cool very helpfull
i just passed. this exam dumps is the same one from prepaway and examcollection. it has all the real test questions.
is this a valid prince2 practitioner dumps?
all are relatable questions
might help me to prepare for the exam
just paid and downlaod the 2 exams using the 50% sale discount. so far i was able to download the pdf and the test engine. all looks good.
i think it should be a,c. option d goes against the principle of building anything custom unless there are no work arounds available
very legible
is this exam accurate or helpful?
please upload dump, i have exam in 2 days
this is useful
question 232 answer should be perimeter not netowrk layer. wrong answer selected
hi team, could you please provide this dump ?
very helpful to clear the exam and understand the concept.
i think it is great that you are helping people when they need it. thanks.
cannot evaluate yet
a laptops wireless antenna is most likely located in the bezel of the lid
good examplae to learn basic
this is useful information
looks usefull
question 81 should be c.
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your NSE7_EFW-7.2, please sign in or create a free account.