Exhibit.Refer to the exhibit, which provides information on BGP neighbors.Which can you conclude from this command output?
Answer(s): C
The BGP state is "Idle", indicating that BGP is attempting to establish a TCP connection with the peer. This is the first state in the BGP finite state machine, and it means that no TCP connection has been established yet. If the TCP connection fails, the BGP state will reset to either active or idle, depending on the configuration.
You can find more information about BGP states and troubleshooting in the following Fortinet Enterprise Firewall 7.2 documents:Troubleshooting BGPHow BGP works
Exhibit.Refer to the exhibit, which contains the partial ADVPN configuration of a spoke.Which two parameters must you configure on the corresponding single hub? (Choose two.)
Answer(s): A,B
For an ADVPN spoke configuration shown, the corresponding hub must have auto-discovery-sender enabled to send shortcut advertisement messages to the spokes. Also, the hub would need to have auto-discovery-forwarder enabled if it is to forward on those shortcut advertisements to other spokes. This allows the hub to inform all spokes about the best path to reach each other. The ike- version does not need to be reconfigured on the hub if it's already set to version 2 and auto- discovery-receiver is not necessary on the hub because it's the one sending the advertisements, not receiving.
FortiOS Handbook - ADVPN
Which FortiGate in a Security I auric sends togs to FortiAnalyzer?
Answer(s): B
Option B is correct because each FortiGate in the Security Fabric can send logs to FortiAnalyzer for centralized logging and analysis12. This allows you to monitor and manage the entire Security Fabric from a single console and view aggregated reports and dashboards.Option A is incorrect because the root FortiGate is not the only device that can send logs to FortiAnalyzer. The root FortiGate is the device that initiates the Security Fabric and acts as the central point of contact for other FortiGate devices3. However, it does not have to be the only log source for FortiAnalyzer.Option C is incorrect because the FortiGate devices performing NAT or UTM are not the only devices that can send logs to FortiAnalyzer. These devices can perform additional security functions on the traffic that passes through them, such as firewall, antivirus, web filtering, etc4. However, they are not the only devices that generate logs in the Security Fabric.Option D is incorrect because the last FortiGate that handled a session in the Security Fabric is not the only device that can send logs to FortiAnalyzer. The last FortiGate is the device that terminates the session and applies the final security policy5. However, it does not have to be the only device that reports the session information to FortiAnalyzer.
=1: Security Fabric - Fortinet Documentation12: FortiAnalyzer Demo63: Security Fabric topology4: Security Fabric UTM features5: Security Fabric session handling
Which configuration can be used to reduce the number of BGP sessions in on IBGP network?
To reduce the number of BGP sessions in an IBGP network, you can use a route reflector, which acts as a focal point for IBGP sessions and readvertises the prefixes to all other peers. To configure a route reflector, you need to enable the route-reflector-client option on the neighbor-group settings of the hub device. This will make the hub device act as a route reflector server and the other devices as route reflector clients. Reference := Route exchange | FortiGate / FortiOS 7.2.0 - Fortinet Documentation
Exhibit.Refer to the exhibit, which contains an active-active toad balancing scenario.During the traffic flow the primary FortiGate forwards the SYN packet to the secondary FortiGate.What is the destination MAC address or addresses when packets are forwarded from the primary FortiGate to the secondary FortiGate?
Answer(s): A
In an active-active load balancing scenario, when the primary FortiGate forwards the SYN packet to the secondary FortiGate, the destination MAC address would be the secondary's physical MAC on port1, as the packet is being sent over the network and the physical MAC is used for layer 2 transmissions.
Share your comments for Fortinet NSE7_EFW-7.2 exam with other users:
i need exam questions nca 6.5 any help please ?
just took the comptia cybersecurity analyst (cysa+) - wished id seeing this before my exam
very helpful
i need this exam
nice questions... are these questions the same of the exam?
need to view
highly appreciate for your sharing.
kindly share this dump. thank you
link plz for download
data quality oecd
rman is one good recovery technology
need it thx
good questions
good one nice revision
i love this thank you i need
question # 142: data governance is not one of the deliverables in the document and content management context diagram.
most answers not correct here
what % of questions do we get in the real exam?
i just want to tell you. i took my microsoft az-104 exam and passed it. your program was awesome. i especially liked your detailed questions and answers and practice tests that made me well-prepared for the exam. thanks to this website!!!
all the best
very usefull document
nice and helpful questions
i found the questions helpful
q 105 . ans is d
i have interest to get a sybase iq dba certification
want to pass exm.
are the answers correct?
good morning, could you please upload this exam again, i need it to test my knowledge in sd-wan with version 7.0.
very nice question
i have learning disability and this exam dumps allowed me to focus on the actual questions and not worry about notes and the those other study materials.
165 should be apt
please upload the dumps, real need of them
any recent feeedback?
question number 2 is indicating you are giving proper questions. observe and change properly.
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your NSE7_EFW-7.2, please sign in or create a free account.