Exhibit.Refer to the exhibit, which provides information on BGP neighbors.Which can you conclude from this command output?
Answer(s): C
The BGP state is "Idle", indicating that BGP is attempting to establish a TCP connection with the peer. This is the first state in the BGP finite state machine, and it means that no TCP connection has been established yet. If the TCP connection fails, the BGP state will reset to either active or idle, depending on the configuration.
You can find more information about BGP states and troubleshooting in the following Fortinet Enterprise Firewall 7.2 documents:Troubleshooting BGPHow BGP works
Exhibit.Refer to the exhibit, which contains the partial ADVPN configuration of a spoke.Which two parameters must you configure on the corresponding single hub? (Choose two.)
Answer(s): A,B
For an ADVPN spoke configuration shown, the corresponding hub must have auto-discovery-sender enabled to send shortcut advertisement messages to the spokes. Also, the hub would need to have auto-discovery-forwarder enabled if it is to forward on those shortcut advertisements to other spokes. This allows the hub to inform all spokes about the best path to reach each other. The ike- version does not need to be reconfigured on the hub if it's already set to version 2 and auto- discovery-receiver is not necessary on the hub because it's the one sending the advertisements, not receiving.
FortiOS Handbook - ADVPN
Which FortiGate in a Security I auric sends togs to FortiAnalyzer?
Answer(s): B
Option B is correct because each FortiGate in the Security Fabric can send logs to FortiAnalyzer for centralized logging and analysis12. This allows you to monitor and manage the entire Security Fabric from a single console and view aggregated reports and dashboards.Option A is incorrect because the root FortiGate is not the only device that can send logs to FortiAnalyzer. The root FortiGate is the device that initiates the Security Fabric and acts as the central point of contact for other FortiGate devices3. However, it does not have to be the only log source for FortiAnalyzer.Option C is incorrect because the FortiGate devices performing NAT or UTM are not the only devices that can send logs to FortiAnalyzer. These devices can perform additional security functions on the traffic that passes through them, such as firewall, antivirus, web filtering, etc4. However, they are not the only devices that generate logs in the Security Fabric.Option D is incorrect because the last FortiGate that handled a session in the Security Fabric is not the only device that can send logs to FortiAnalyzer. The last FortiGate is the device that terminates the session and applies the final security policy5. However, it does not have to be the only device that reports the session information to FortiAnalyzer.
=1: Security Fabric - Fortinet Documentation12: FortiAnalyzer Demo63: Security Fabric topology4: Security Fabric UTM features5: Security Fabric session handling
Which configuration can be used to reduce the number of BGP sessions in on IBGP network?
To reduce the number of BGP sessions in an IBGP network, you can use a route reflector, which acts as a focal point for IBGP sessions and readvertises the prefixes to all other peers. To configure a route reflector, you need to enable the route-reflector-client option on the neighbor-group settings of the hub device. This will make the hub device act as a route reflector server and the other devices as route reflector clients. Reference := Route exchange | FortiGate / FortiOS 7.2.0 - Fortinet Documentation
Exhibit.Refer to the exhibit, which contains an active-active toad balancing scenario.During the traffic flow the primary FortiGate forwards the SYN packet to the secondary FortiGate.What is the destination MAC address or addresses when packets are forwarded from the primary FortiGate to the secondary FortiGate?
Answer(s): A
In an active-active load balancing scenario, when the primary FortiGate forwards the SYN packet to the secondary FortiGate, the destination MAC address would be the secondary's physical MAC on port1, as the packet is being sent over the network and the physical MAC is used for layer 2 transmissions.
Share your comments for Fortinet NSE7_EFW-7.2 exam with other users:
all questions are more important
ques 4 answer should be c ie automatically recover from failure
very very useful page
the exams are giving me an eye opener
3rd so far, need to cover more
aligns with the pecd notes
question 4: b securityadmin is the correct answer. https://docs.snowflake.com/en/user-guide/security-access-control-overview#access-control-framework
kindly please share dumps
it is very useful, thank you
need safe rte dumps
can you upload the cis - cpg dumps
q6 = 1. download odt application 2. create a configuration file (xml) 3. setup.exe /download to download the installation files 4. setup.exe /configure to deploy the application
great material
could you please upload sap c_arsor_2302 questions? it will be very much helpful.
vraag 20c: rsa veilig voor symmtrische cryptografie? antwoord c is toch fout. rsa is voor asymmetrische cryptogafie??
so far good
question 31 has obviously wrong answers. tls and ssl are used to encrypt data at transit, not at rest.
pls provide dump for 1z0-1080-23 planning exams
could you please upload the exam?
please upload this
good material
lets see if this is good stuff...
useful information
intéressant
thank you for making the interactive questions
questions are accurate
i need questions/dumps for this exam.
i need this exam, when will it be uploaded
i need the dumps !
very helpful
good source
my 3rd test and passed on first try. hats off to this brain dumps site.
please upload it
does anybody know if are these real exam questions?
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your NSE7_EFW-7.2, please sign in or create a free account.