Refer to the exhibit.An administrator configures SD-WAN rules for a DIA setup using the FortiGate GUI. The page to configure the source and destination part of the rule looks as shown in the exhibit. The GUI page shows no option to configure an application as the destination of the SD-WAN rule Why?
Answer(s): D
You are planning a new SD-WAN deployment with the following criteria:- Two regions- Most of the traffic is expected to remain within its region- No requirement for inter-region ADVPNTo remain within the recommended best practices, which routing protocol should you select for the overlays?
Answer(s): B
For SD-WAN deployments that span multiple regions--where most traffic is intra-region and there is no requirement for inter-region ADVPN--the best practice is to use IBGP with BGP on loopback interfaces for routing within each region and EBGP between the regions. This approach ensures robust and scalable routing, isolates regional routing domains, and enables policy control at region boundaries. BGP on loopback is preferred for its reliability and flexibility, as it enables peering that is not tied to specific physical interfaces. EBGP between regions allows each region to maintain independent routing policies and summarization, optimizing performance and manageability. By separating IBGP (intra-region) and EBGP (inter-region), you create a modular architecture that scales easily and simplifies fault isolation and troubleshooting.
Fortinet SD-WAN Reference Architecture Guide 7.4, "Regional Routing Best Practices"FortiOS 7.4 SD-WAN Overlay Design Guidelines
Exhibit.The administrator configured the IPsec tunnel VPN1 on a FortiGate device with the parameters shown in exhibit.Based on the configuration, which three conclusions can you draw about the characteristics and requirements of the VPN tunnel? (Choose three.)
Answer(s): B,C,E
This configuration demonstrates a typical IPsec setup for SD-WAN overlays where the hub side requires a manually defined tunnel IP address, and the spoke can be flexibly configured, including interoperability with third-party IPsec devices. As described in the Fortinet SD-WAN Architect Guide:"For some overlays, the tunnel interface IP is configured statically on the hub side, which allowsmore control over overlay subnetting and facilitates the use of user-defined overlay IP addresses. This approach is also a requirement for compatibility with non-FortiGate endpoints, such as third- party IPsec devices that may not support dynamic address assignment via IKE or proprietary mechanisms." This enables hybrid SD-WAN environments and advanced designs involving external partners or cloud services. Overlay IP flexibility is critical for route control and segmentation.
FortiOS 7.4 SD-WAN Reference Architecture, "Overlay IP Address Management"SD-WAN 7.4 Concept Guide, Section: "Interoperability with Third-Party Devices"
You have a FortiGate configuration with three user-defined SD-WAN zones and two members in each of these zones. One SD-WAN member is no longer in use in health-check and SD-WAN rules. You want to delete it.What happens if you delete the SD-WAN member from the FortiGate GUI?
Answer(s): A
Refer to the exhibits.The exhibits show the source NAT (SNAT) global setting. port2 interface settings, and the routing table on FortiGate.The administrator increases the member priority on port2 to 20.Upon configuration changes and the receipt of new packets, which two actions does FortiGate perform on existing sessions established over port2? (Choose two.)
Answer(s): D,E
When the member priority of a port is increased (e.g., port2 to 20), FortiGate evaluates existing sessions and applies "dirty" flags where applicable. The SD-WAN session management mechanism is described in detail: "Upon a change in SD-WAN member priority, all existing sessions using that member are marked as dirty. For SNAT sessions, the gateway information is updated to ensure future packets are routed through the newly preferred member, in this case, port1. This automatic re- evaluation allows SD-WAN to dynamically respond to topology or priority changes, maintaining optimal routing." This is fundamental to seamless failover and session persistence in Fortinet SD- WAN, ensuring active flows are redirected based on updated priorities or health status.
FortiOS 7.4 SD-WAN Concept Guide, "Session Management During Path Change"FortiGate CLI diagnose sys session list
Refer to the exhibits.The exhibits show the configuration for SD-WAN performance. SD-WAN rule, the application IDs of Facebook and YouTube along with the firewall policy configuration and the underlay zone status.Which two statements are true about the health and performance of SD-WAN members 3 and 4? (Choose two.)
Answer(s): B,D
When you use the command diagnose sys session list, how do you identify the sessions that correspond to traffic steered according to SD-WAN rules?
When using the diagnose sys session list command, SD-WAN-specific session steering is indicated by the presence of the sdwan_service_id field in the session data. This identifier ties the session directly to a specific SD-WAN rule or service. As noted in the Fortinet documentation: "Sessions that are handled according to SD-WAN rules will include a service ID tag (sdwan_service_id) in their session listing. This allows administrators to correlate live sessions with SD-WAN policy matches for troubleshooting and visibility." This is a crucial diagnostic tool, as it distinguishes between traffic managed by traditional routing and that explicitly controlled by SD-WAN steering logic, aiding in operational insight and troubleshooting.
FortiOS 7.4 CLI Reference, "diagnose sys session list: SD-WAN Service ID Tagging"SD-WAN 7.4 Concept Guide, Section: "Session Identification for SD-WAN Traffic"
SD-WAN interacts with many other FortiGate features. Some of them are required to allow SD-WAN to steer the traffic.Which three configuration elements that you must configure before FortiGate can steer traffic according to SD-WAN rules? (Choose three.)
Answer(s): A,B,E
Before FortiGate can steer traffic according to SD-WAN rules, certain configuration elements must be present. The guide states:"SD-WAN is not a standalone feature and interacts with several fundamental FortiGate configurations. Specifically, you must: (1) Define the interfaces (physical, VLAN, or IPsec) that will act as SD-WAN members, (2) Create firewall policies to allow traffic to be steered by SD-WAN, and (3)Set up routing so that traffic has valid routes via SD-WAN members. Without these, SD-WAN rules will not be able to match or steer any traffic."Security profiles and traffic shaping are not mandatory for basic SD-WAN steering but can be layered on for enhanced security and QoS once foundational elements are present.
FortiOS 7.4 SD-WAN Concept Guide, "Prerequisite Configuration Elements for SD-WAN Steering
Share your comments for Fortinet NSE6_SDW_AD-7.6 exam with other users:
might help me to prepare for the exam
just paid and downlaod the 2 exams using the 50% sale discount. so far i was able to download the pdf and the test engine. all looks good.
i think it should be a,c. option d goes against the principle of building anything custom unless there are no work arounds available
very legible
is this exam accurate or helpful?
please upload dump, i have exam in 2 days
this is useful
question 232 answer should be perimeter not netowrk layer. wrong answer selected
nice questions
hi team, could you please provide this dump ?
very helpful to clear the exam and understand the concept.
i think it is great that you are helping people when they need it. thanks.
cannot evaluate yet
a laptops wireless antenna is most likely located in the bezel of the lid
good examplae to learn basic
this is useful information
looks usefull
question 81 should be c.
question 18 : response isnt a ?
plaese add questions
is dumps still valid ?
thanks for this
please upload questions
please upload the question dump for professional machinelearning
question 4 answer is c. this site shows the correct answer as b. "adopt a consumption model" is clearly a cost optimization design principle. looks like im done using this site to study!!!
number 52 answer is d
just started preparing for my exam , and this site is so much help
question 35 is incorrect, the correct answer is c, it even states so: explanation: when a vm is infected with ransomware, you should not restore the vm to the infected vm. this is because the ransomware will still be present on the vm, and it will encrypt the files again. you should also not restore the vm to any vm within the companys subscription. this is because the ransomware could spread to other vms in the subscription. the best way to restore a vm that is infected with ransomware is to restore it to a new azure vm. this will ensure that the ransomware is not present on the new vm.
i would like to take psm1 exam.
cbd and pdb are key to the database
the purchase and download process is very much streamlined. the xengine application is very nice and user-friendly but there is always room for improvement.
please upload p_sapea_2023
anyone use this? the question dont seem to follow other formats and terminology i have been studying im getting worried
good questions
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your NSE6_SDW_AD-7.6, please sign in or create a free account.