Refer to the exhibit.Based on this partial configuration, what are the two possible outcomes when FortiGate enters conserve mode? (Choose two.)
Answer(s): C,D
An administrator has configured a dialup IPsec VPN on FortiGate with add-route enabled. However, the static route is not showing in the routing table. Which two statements about this scenario are correct? (Choose two.)
Answer(s): B,C
With a dialup IPsec VPN on FortiGate, when add-route is enabled, FortiGate will only install the corresponding route when it has enough negotiated information from the tunnel. In FortiOS 7.6, that means the route is tied to the Phase 2 (Quick Mode) selectors and is created dynamically when the IPsec SA is actually up.B . The administrator must ensure phase 2 is successfully establishedThis is required. FortiGate does not install the add-route route just because Phase 1 exists or because the configuration is present. The route is added when the tunnel is effectively usable, which requires Phase 2 (IPsec SA) to be up. If Phase 2 is not established, there is no active SA and FortiGate will not inject the related route into the routing table.So, if the static route is not showing, one correct explanation is that Phase 2 is not up.C . The administrator must define the remote network correctly in the phase 2 selectorsThis is also required. For dialup tunnels, FortiGate derives what route to add from the remote subnet(s) defined in the Phase 2 selector (proxy ID). If the remote network in Phase 2 is missing, incorrect, or too broad/too narrow in a way that prevents negotiation, the tunnel either won't come up (so no route), or the route that would be installed won't match what the administrator expects.So, another correct explanation is that the Phase 2 remote network is not correctly defined, preventing the correct route from being created.Why the other options are incorrectA . Policy route instead of a static routeAdd-route does not require policy routes. It is specifically a feature that injects a route (route-table entry) associated with the IPsec tunnel/SA and the Phase 2 selector networks.D . Enable a dynamic routing protocolDynamic routing protocols (OSPF/BGP/RIP) are not required for add-route. Add-route is independent of dynamic routing and works by installing routes locally based on the negotiated selectors.
Refer to the exhibit.A RADIUS server configuration is shown.An administrator added a configuration for a new RADIUS server While configuring, the administrator enabled Include in every user group What is the impact of enabling Include in every user group in a RADIUS configuration?
Answer(s): A
Based on the FortiOS 7.6 Authentication and User Group documentation, the correct answer is A .Meaning of "Include in every user group" (FortiOS 7.6)When configuring a RADIUS server on FortiGate, enabling Include in every user group has a very specific and documented effect:The configured RADIUS server object is automatically added to all FortiGate user groups.As a result, any user who successfully authenticates against that RADIUS server becomes a valid member of every FortiGate user group, unless additional group filtering (such as RADIUS attributes) is applied.This simplifies configuration when the same external authentication source must be accepted across multiple firewall policies that reference different user groups.This behavior is explicitly described in the FortiOS 7.6 Administrator Guide under RADIUS authentication servers and user groups.Why Option A is CorrectFortiGate user groups can include:Local usersLDAP serversRADIUS serversEnabling Include in every user group causes FortiGate to:Insert the RADIUS server into all existing and future FortiGate user groupsTherefore, all users authenticating via this RADIUS server are implicitly allowed in every FortiGate user group.This is exactly what option A describes.Why the Other Options Are IncorrectB: FortiGate does not push users or groups into the RADIUS server. Authentication is always initiated by FortiGate toward RADIUS.C: FortiGate does not manage or modify RADIUS-side group definitions.D: LDAP and RADIUS user groups are separate authentication mechanisms; this setting does not merge or affect LDAP groups.
You have created a web filter profile named restrictmedia-profile with a daily category usage quota.When you are adding the profile to the firewall policy, the restrict_media-profile is not listed in the available web profile drop down.What could be the reason?
Answer(s): D
In FortiOS 7.6, web filter profiles are inspection-mode dependent. Certain advanced web filtering features--such as daily category usage quota--are only supported when the firewall policy is operating in proxy-based inspection mode.Why the profile is not visibleThe profile restrictmedia-profile includes a daily category usage quota.Daily quotas are a proxy-based web filtering feature.If the firewall policy is configured with:Inspection mode: Flow-basedThen FortiGate will not display proxy-only web filter profiles in the Web Filter drop-down list.FortiGate automatically filters the available profiles based on feature compatibility with the policy's inspection mode.This behavior is explicitly documented in the FortiOS 7.6 Web Filtering and Inspection Mode Compatibility sections.Why the other options are incorrectA . Already referenced in another firewall policyWeb filter profiles can be reused across multiple policies. This does not hide them.B . Firewall policy is in no-inspection mode instead of deep-inspection SSL inspection depth affects HTTPS visibility, not whether a web filter profile appears in the drop- down list.C . Naming convention restrictionFortiOS does not restrict profile selection based on naming conventions.
Refer to the exhibits.A diagram of a FortiGate device connected to the network, as well as the firewall policy and IP pool configuration on the FortiGate device are shown.Two PCs. PC1 and PC2, are connected behind FortiGate and can access the internet successfully. However, when the administrator adds a third PC to the network (PC3), the PC cannot connect to the internet.Based on the information shown in the exhibit, which two configuration options can the administrator use to fix the connectivity issue for PC3? (Choose two.)
Answer(s): B,D
From the exhibits:The firewall policy has NAT enabled and is configured to Use Dynamic IP Pool.The selected IP pool (Internet-pool) is configured as:Type: One-to-OneExternal IP Range: 100.65.0.110100.65.0.111 (only two public IPs)PC1 and PC2 can access the internet because each one-to-one NAT mapping consumes one public IP from the pool. When PC3 is added, there is no third public IP available in the pool, so FortiGate cannot allocate a one-to-one mapping for PC3 and the session fails.FortiOS behavior here is standard: with one-to-one IP pools, the available pool size limits how many distinct internal sources can be translated concurrently (depending on allocation and sessions), and a pool with only two IPs will not reliably support three separate hosts needing translations.Therefore, the administrator can fix this in two valid ways:B . In the IP pool configuration, set end ip to 100.65.0.112.This expands the pool by adding an additional public IP address, making three public IPs available (.110, .111, .112), so PC3 can be assigned an address for one-to-one NAT.D . In the IP pool configuration, set type to overload.Changing the pool type to overload enables PAT (many-to-one), allowing multiple internal hosts (PC1, PC2, PC3) to share the pool address(es) using different source ports. This removes the "one public IP per internal host" limitation inherent to one-to-one pools.Why the other options are not correct:A . Multiple Interface Policies is unrelated to IP pool exhaustion and does not solve NAT allocation limits.C . match-vip affects VIP matching behavior for destination NAT/virtual IP usage and does not address the source NAT pool shortage causing PC3 to fail.
Which two statements are correct when the FortiGate device enters conserve mode? (Choose two.)
Answer(s): A,C
Refer to the exhibits.Based on the current HA status, an administrator updates the override and priority parameters on HQ-NGFW-1 and HQ-NGFW-2 as shown in the exhibits.What would be the expected outcome in the HA cluster?
From the current HA status, HQ-NGFW-1 is the primary and HQ-NGFW-2 is the secondary.The administrator then changes these HA parameters:HQ-NGFW-1: set override disable, set priority 90HQ-NGFW-2: set override enable, set priority 110In FGCP (A-P mode), the override (preemption) feature controls whether a higher-priority unit is allowed to take over the primary role.When override is enabled, the cluster will prefer (and can re-elect) the unit with the highest device priority to become primary (preempting a lower-priority primary when conditions trigger re-election behavior as defined by FGCP).Here, HQ-NGFW-2 has:override enabled higher priority (110) than HQ-NGFW-1 (90)Therefore, the expected result is that HQ-NGFW-2 becomes the primary.Why the other options are incorrect:B is incorrect because it claims HQ-NGFW-2 has lower priority (it is higher: 110 > 90).C is incorrect because a mismatch in the override setting is not what causes the "configuration out of sync" condition shown in get system ha status (that is about synchronized configuration databases, not a requirement that override values must match to remain in-sync).D is incorrect because HA settings like override/priority are not synchronized in the way regular configuration objects are; they are device-level HA parameters.
Refer to the exhibitA firewall policy to enable active authentication is shown.When attempting to access an external website using an active authentication method, the user is not presented with a login prompt. What is the most likely reason for this situation?
Based on the exhibit and FortiOS 7.6 Active Authentication (captive portal) behavior, the most likely reason the user is not presented with a login prompt is that DNS is missing from the firewall policy.What the exhibit showsThe firewall policy configured for active authentication includes:Source: HQ_SUBNET and Remote-usersDestination: allServices:HTTPHTTPSALL_ICMPSecurity Profiles: Web filter and SSL inspection enabledAuthentication: Active (user group referenced)DNS is not included as a service in the policy.Why DNS is required for active authenticationIn FortiOS 7.6, active authentication (captive portal) works as follows:The user attempts to access a website using a URL (for example, www.example.com).The client must first perform a DNS lookup to resolve the domain name.FortiGate intercepts the initial HTTP/HTTPS request and redirects the user to the authentication portal.If DNS traffic is blocked or not allowed:The hostname cannot be resolved.The HTTP/HTTPS request never properly occurs.FortiGate has nothing to intercept, so the login prompt is never triggered.This is explicitly documented in the FortiOS 7.6 Authentication and Captive Portal requirements, which state that DNS must be permitted for captive portalbased authentication to function correctly.Why the other options are incorrectA . No matching user account exists for this userIncorrect.If the user account did not exist, the login page would still appear, but authentication would fail after credentials are entered.B . The Remote-users group must be set up correctly in the FSSO configurationIncorrect.This policy is using active authentication, not FSSO.FSSO configuration is irrelevant for active authentication login prompts.C . The Remote-users group is not added to the DestinationIncorrect.User groups are applied in the Source field for authentication-based policies.Destination does not accept user groups.
Share your comments for Fortinet NSE4_FGT_AD-7.6 exam with other users:
kindly upload the dumps
still learning
excellent way to learn
help so much
understand sql col.
i would give 5 stars to this website as i studied for az-800 exam from here. it has all the relevant material available for preparation. i got 890/1000 on the test.
this is nice.
q55- the ridac workflow can be modified using flow designer, correct answer is d not a
by far this is the most accurate exam dumps i have ever purchased. all questions are in the exam. i saw almost 90% of the questions word by word.
i cleared the az-104 exam by scoring 930/1000 on the exam. it was all possible due to this platform as it provides premium quality service. thank you!
question # 232: accessibility, privacy, and innovation are not data quality dimensions.
looks wrong answer for 443 question, please check and update
great question
question: a user wants to start a recruiting posting job posting. what must occur before the posting process can begin? 3 ans: comment- option e is incorrect reason: as part of enablement steps, sap recommends that to be able to post jobs to a job board, a user need to have the correct permission and secondly, be associated with one posting profile at minimum
answer to question 72 is d [sys_user_role]
please provide the pdf
hey guys, just to let you all know that i cleared my 312-38 today within 1 hr with 100 questions and passed. thank you so much brain-dumps.net all the questions that ive studied in this dump came out exactly the same word for word "verbatim". you rock brain-dumps.net!!! section name total score gained score network perimeter protection 16 11 incident response 10 8 enterprise virtual, cloud, and wireless network protection 12 8 application and data protection 13 10 network défense management 10 9 endpoint protection 15 12 incident d
very helpful
useful questions
page :20 https://exam-dumps.com/snowflake/free-cof-c02-braindumps.html?p=20#collapse_453 q 74: true or false: pipes can be suspended and resumed. true. desc.: pausing or resuming pipes in addition to the pipe owner, a role that has the following minimum permissions can pause or resume the pipe https://docs.snowflake.com/en/user-guide/data-load-snowpipe-intro
i want hcia exam dumps
good training
very useful
yes need this exam dumps
these questions are a great eye opener
thank you for providing these questions and answers. they helped me pass my exam. you guys are great.
good knowledge
answer 10 should be a because only a new project will be created & the organization is the same.
can you please upload the dump again
is it legit questions from sap certifications ?
question 16 should be b (changing the connector settings on the monitor) pc and monitor were powered on. the lights on the pc are on indicating power. the monitor is showing an error text indicating that it is receiving power too. this is a clear sign of having the wrong input selected on the monitor. thus, the "connector setting" needs to be switched from hdmi to display port on the monitor so it receives the signal from the pc, or the other way around (display port to hdmi).
q 10. ans is d (in the target org: open deployment settings, click edit next to the source org. select allow inbound changes and save
i purchased this exam dumps from another website with way more questions but they were all invalid and outdate. this exam dumps was right to the point and all from recent exam. it was a hard pass.
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your NSE4_FGT_AD-7.6, please sign in or create a free account.