Refer to the exhibit.An administrator configures SD-WAN rules for a DIA setup using the FortiGate GUI. The page to configure the source and destination part of the rule looks as shown in the exhibit. The GUI page shows no option to configure an application as the destination of the SD-WAN rule Why?
Answer(s): D
You are planning a new SD-WAN deployment with the following criteria:- Two regions- Most of the traffic is expected to remain within its region- No requirement for inter-region ADVPNTo remain within the recommended best practices, which routing protocol should you select for the overlays?
Answer(s): B
For SD-WAN deployments that span multiple regions--where most traffic is intra-region and there is no requirement for inter-region ADVPN--the best practice is to use IBGP with BGP on loopback interfaces for routing within each region and EBGP between the regions. This approach ensures robust and scalable routing, isolates regional routing domains, and enables policy control at region boundaries. BGP on loopback is preferred for its reliability and flexibility, as it enables peering that is not tied to specific physical interfaces. EBGP between regions allows each region to maintain independent routing policies and summarization, optimizing performance and manageability. By separating IBGP (intra-region) and EBGP (inter-region), you create a modular architecture that scales easily and simplifies fault isolation and troubleshooting.
Fortinet SD-WAN Reference Architecture Guide 7.4, "Regional Routing Best Practices"FortiOS 7.4 SD-WAN Overlay Design Guidelines
Exhibit.The administrator configured the IPsec tunnel VPN1 on a FortiGate device with the parameters shown in exhibit.Based on the configuration, which three conclusions can you draw about the characteristics and requirements of the VPN tunnel? (Choose three.)
Answer(s): B,C,E
This configuration demonstrates a typical IPsec setup for SD-WAN overlays where the hub side requires a manually defined tunnel IP address, and the spoke can be flexibly configured, including interoperability with third-party IPsec devices. As described in the Fortinet SD-WAN Architect Guide:"For some overlays, the tunnel interface IP is configured statically on the hub side, which allows more control over overlay subnetting and facilitates the use of user-defined overlay IP addresses. This approach is also a requirement for compatibility with non-FortiGate endpoints, such as third- party IPsec devices that may not support dynamic address assignment via IKE or proprietary mechanisms." This enables hybrid SD-WAN environments and advanced designs involving external partners or cloud services. Overlay IP flexibility is critical for route control and segmentation.
FortiOS 7.4 SD-WAN Reference Architecture, "Overlay IP Address Management"SD-WAN 7.4 Concept Guide, Section: "Interoperability with Third-Party Devices"
You have a FortiGate configuration with three user-defined SD-WAN zones and two members in each of these zones. One SD-WAN member is no longer in use in health-check and SD-WAN rules. You want to delete it.What happens if you delete the SD-WAN member from the FortiGate GUI?
Answer(s): A
Refer to the exhibits.The exhibits show the source NAT (SNAT) global setting. port2 interface settings, and the routing table on FortiGate.The administrator increases the member priority on port2 to 20.Upon configuration changes and the receipt of new packets, which two actions does FortiGate perform on existing sessions established over port2? (Choose two.)
Answer(s): D,E
When the member priority of a port is increased (e.g., port2 to 20), FortiGate evaluates existing sessions and applies "dirty" flags where applicable. The SD-WAN session management mechanism is described in detail: "Upon a change in SD-WAN member priority, all existing sessions using that member are marked as dirty. For SNAT sessions, the gateway information is updated to ensure future packets are routed through the newly preferred member, in this case, port1. This automatic re- evaluation allows SD-WAN to dynamically respond to topology or priority changes, maintaining optimal routing." This is fundamental to seamless failover and session persistence in Fortinet SD- WAN, ensuring active flows are redirected based on updated priorities or health status.
FortiOS 7.4 SD-WAN Concept Guide, "Session Management During Path Change"FortiGate CLI diagnose sys session list
Refer to the exhibits.The exhibits show the configuration for SD-WAN performance. SD-WAN rule, the application IDs of Facebook and YouTube along with the firewall policy configuration and the underlay zone status.Which two statements are true about the health and performance of SD-WAN members 3 and 4? (Choose two.)
Answer(s): B,D
When you use the command diagnose sys session list, how do you identify the sessions that correspond to traffic steered according to SD-WAN rules?
When using the diagnose sys session list command, SD-WAN-specific session steering is indicated by the presence of the sdwan_service_id field in the session data. This identifier ties the session directly to a specific SD-WAN rule or service. As noted in the Fortinet documentation: "Sessions that are handled according to SD-WAN rules will include a service ID tag (sdwan_service_id) in their session listing. This allows administrators to correlate live sessions with SD-WAN policy matches for troubleshooting and visibility." This is a crucial diagnostic tool, as it distinguishes between traffic managed by traditional routing and that explicitly controlled by SD-WAN steering logic, aiding in operational insight and troubleshooting.
FortiOS 7.4 CLI Reference, "diagnose sys session list: SD-WAN Service ID Tagging"SD-WAN 7.4 Concept Guide, Section: "Session Identification for SD-WAN Traffic"
SD-WAN interacts with many other FortiGate features. Some of them are required to allow SD-WAN to steer the traffic.Which three configuration elements that you must configure before FortiGate can steer traffic according to SD-WAN rules? (Choose three.)
Answer(s): A,B,E
Before FortiGate can steer traffic according to SD-WAN rules, certain configuration elements must be present. The guide states:"SD-WAN is not a standalone feature and interacts with several fundamental FortiGate configurations. Specifically, you must: (1) Define the interfaces (physical, VLAN, or IPsec) that will act as SD-WAN members, (2) Create firewall policies to allow traffic to be steered by SD-WAN, and (3) Set up routing so that traffic has valid routes via SD-WAN members. Without these, SD-WAN rules will not be able to match or steer any traffic."Security profiles and traffic shaping are not mandatory for basic SD-WAN steering but can be layered on for enhanced security and QoS once foundational elements are present.
FortiOS 7.4 SD-WAN Concept Guide, "Prerequisite Configuration Elements for SD-WAN Steering
Share your comments for Fortinet FCSS_SDW_AR-7.6 exam with other users:
i am writing this exam tomorrow and have dumps
can i have the icdl excel exam
please upload it
hye when will post again the past year question for this h13-311_v3 part since i have to for my test tommorow…thank you very much
on question 22, option b-once per session is also valid.
this website is very helpful
its my first time exam
correct answers are device configuration-enable the automatic installation of webview2 runtime. & policy management- prevent users from submitting feedback.
is this dump still valid? today is 9-july-2023
i need this exam.. please upload these are really helpful
please upload the oracle 1z0-1059-22 dumps
very good questions
nice, first step to exams
is this valid for chfiv9 as well... as i am reker 3rd time...
great exam for people taking 220-1101
this is very helpfull for me
just started preparing for the exam
these are the type of questions i need.
does this actually work? are they the exam questions and answers word for word?
thanks for providing these questions
interesting
these dumps are pretty good.
good questions
dbua is used for upgrading oracle database
i am thrilled to say that i passed my amazon web services mls-c01 exam, thanks to study materials. they were comprehensive and well-structured, making my preparation efficient.
please upload latest ibm ace c1000-056 dumps
if only explanations were provided...
yes .. i need the dump if you can help me
good morning, could you please upload this exam again?
hi please upload sre foundation and practitioner exam questions
the exam is listed as 80 questions with a pass mark of 70%, how is your 50 questions related?
all questions are so important and covers all ccna modules
q 44. ans:- b (goto setup > order settings > select enable optional price books for orders) reference link --> https://resources.docs.salesforce.com/latest/latest/en-us/sfdc/pdf/sfom_impl_b2b_b2b2c.pdf(decide whether you want to enable the optional price books feature. if so, select enable optional price books for orders. you can use orders in salesforce while managing price books in an external platform. if you’re using d2c commerce, you must select enable optional price books for orders.)
"cost of replacing data if it were lost" is also correct.
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your FCSS_SDW_AR-7.6, please sign in or create a free account.