CWNP PW0-100 Wireless LAN Administration, Certified Wireless Network Administrator (CWNA) PW0-100 Dumps in PDF

Free CWNP PW0-100 Real Questions (page: 7)

Which of the following is true of a 2.4 GHz RF link at a distance of 5 miles (8 kilometers).
(Choose all that apply)

  1. RF Line of Sight is required.
  2. Visual Line of Sight is required.
  3. Earth bulge must be factored into calculations.
  4. The Fresnel Zone must be at least 60% clear of obstructions.
  5. High gain omni-directional antenna.

Answer(s): A,D

Explanation:

From the study guide, Visual LOS is not required for a successful point-to-point connection. However RF LOS is required. Additionally, the Fresnel zone must be at least 60% clear of obstructions. Earth bulge is only factored in for greater then 7 mile links.



Which two RF spread spectrum technologies does IEEE specify in the 802.11 standard? (Choose two)

  1. Infrared
  2. Frequency Hopping
  3. Direct Sequencing
  4. Wide Band

Answer(s): B,C

Explanation:

REF FOR B: a typical 802.11 frequency hopping WLAN might be implemented as an enterprise wireless networking solution while HomeRF is only implemented in home environments due to lower output power restrictions by the FCC OR
Frequency agility refers to the radio's
ability to change transmission frequency abruptly within the usable RF frequency band. In the case of frequency hopping wireless LANs, the usable portion of the 2.4 GHz ISM band is 83.5 MHz, per FCC regulation and the IEEE 802.11 standard.
REF FOR C//
In the 2.4 GHz ISM band, the IEEE specifies the use of DSSS at a data rate of 1 or 2 Mbps under the 802.11 standard.Under the 802.11b standard-sometimes called highrate wireless-data rates of 5.5 and 11 Mbps are specified.



What are the two types of scanning used with wireless LANs? (Choose all that apply)

  1. Passive
  2. Beacon
  3. Probe
  4. Active

Answer(s): A,D

Explanation:

When you install, configure, and finally start up a wireless LAN client device such as a USB client or PCMCIA card, the client will automatically "listen" to see if there is a wireless LAN within range. The client is also discovering if it can associate with that wireless LAN. This process of listening is called scanning. Scanning occurs before any other process, since scanning is how the client finds the network. There are two kinds of scanning: passive scanning and active scanning. In finding an access point, client stations follow a trail of breadcrumbs left by the access point. These breadcrumbs are called service set identifiers (SSID) and beacons. These tools serve as a means for a client station to find any and all access points.



A wireless portal interconnects LANs conforming to what IEEE standards? (Choose two)

  1. 802.11 and 802.3
  2. 802.3 and 802.5
  3. 802.5 and 802.11
  4. 802.10 and 802.11
  5. 802.5 and 802.10

Answer(s): A,C

Explanation:

An access point is considered a portal because it allows client connectivity from an 802.11 network to 802.3 or 802.5 networks. Access points are available with many different hardware and software options. The most common of these options are:
? Fixed or Detachable Antennas
? Advanced Filtering Capabilities
? Removable (Modular) Radio Cards
? Variable Output Power
? Varied Types of Wired Connectivity



Choose the organization that creates wireless LAN standards.

  1. IEEE
  2. WLANA
  3. WECA
  4. Wi-Fi

Answer(s): A



Under 802.11 standard, what modulation types are used when transmitting data using DSSS? (Choose all that apply)

  1. CCK
  2. GFSK
  3. BPSK
  4. QPSK
  5. 64QAM

Answer(s): C,D

Explanation:

The high data rate of 802.11b-compliant devices is the result of using a different coding technique. Though the system is still a direct sequencing system, the way the chips are coded (CCK rather than Barker Code) along with the way the information is modulated (QPSK at 2, 5.5, & 11 Mbps and BPSK at 1 Mbps) allows for a greater amount of data to be transferred in the same time frame. 802.11b compliant products operate only in the 2.4 GHz ISM band between 2.4000 and 2.4835 GHz.



The ETS1 standard being developed to compete against 802.11a is known as?

  1. HomeRF
  2. OpenAir
  3. HiperLan/2
  4. Bluetooth

Answer(s): C

Explanation:

The standards ETSI has established, HiPerLAN/2 for example, directly compete against standards created by the IEEE such as 802.11A. There has been much discussion about IEEE and ETSI unifying on certain wireless technologies, but nothing has materialized as of this writing. This effort is referred to as the "5UP" initiative for "5 GHz Unified Protocol." The IEEE's attempt at interoperability with ETSI's HiperLAN/2 standard is the new forthcoming 802.11h standard.



WECA requires which of the following WEP security settings for Wi-Fi certification?

  1. Single 104-bit key.
  2. Dial 40-bit keys.
  3. Single 128-bit key.
  4. Single 40-bit key.

Answer(s): D

Explanation:

The 802.11 standard leaves WEP implementation up to wireless LAN manufacturers, so each vendor's implementation of WEP keys may or may not be the same, adding another weakness to WEP. Even WECA's Wi-Fi interoperability standard tests include only 40- bit WEP keys.
Among WECA's list of interoperability checks is the use of 40-bit WEP keys. Note that 40- and 64-bit keys are the same thing. A 40-bit "secret" key is concatenated with a 24- bit Initialization Vector (IV) to reach the 64-bits. In the same manner, 104- and 128-bit keys are the same. WECA does not specify interoperability of 128-bit keys; hence, no compatibility is to be expected between vendors displaying the Wi-Fi seal when using 128-bit WEP keys.



Share your comments for CWNP PW0-100 exam with other users:

A
AI Tutor Explanation
5/7/2026 11:34:48 PM

As an administrator for this subscription, you have been tasked with recommending a solution that prohibits users from copying corporate information from managed applications installed on unmanaged devices. Which of the following should you recommend? Windows Virtual Desktop. Microsoft Intune. Windows AutoPilot. Azure AD Application Proxy.

  • Microsoft Intune

Reason: Intune can enforce app protection policies (MAM) on managed apps, even on unmanaged devices, to prevent data leakage (e.g., restricting copy/paste, saving to non-approved apps, etc.). The other options don’t address data protection within apps on unmanaged devices.

A
AI Tutor Explanation
5/4/2026 2:43:10 AM

Question 34:

  • Question 34 asks: Which role(s) has the capability to create Policies? Choose two.
  • Likely correct roles: Compliance Manager and Compliance admin (A and B). These roles typically have policy governance rights to create and manage policies.
  • Why not the others: Compliance User is usually a limited user, not allowed to create policies. Risk Manager focuses on risks, not policy creation in standard setups.
  • Note on the provided key: The answer shown is “C” (Compliance User), which conflicts with “Choose two.” This is probably a key error. In practice, verify against your instance’s ACLs or official docs.
  • Quick check tip: In ServiceNow, review the ACLs and role permissions for the Policy records to see which roles can create policies.

A
AI Tutor Explanation
4/29/2026 11:59:58 PM

function of appnav in sdwan

  • AppNav (Application Navigation) is the Cisco SD-WAN feature that provides application-level visibility and control.
  • It maintains a catalog of applications (AppIDs) with attributes (ports/protocols, categories) and classifies traffic accordingly.
  • It allows policy authors to reference apps by name in policies, enabling application-aware routing, QoS, and service chaining based on the app’s requirements.
  • The SD-WAN fabric uses AppNav data to steer traffic along the best path, improving user experience for critical apps while optimizing WAN usage.

A
AI Tutor Explanation
4/29/2026 5:25:25 AM

Question 1:

  • Correct answer: C. Extract the hardware ID information of each computer to a CSV file and upload the file from the Microsoft Intune admin center.

  • Why this is correct

A
AI Tutor Explanation
4/29/2026 5:23:14 AM

Question 5:

  • Correct answer: A. User4 and User1 only

  • Why this is correct:
- The Automatic Enrollment setting in Intune has MDM user scope: GroupA. Only users in GroupA can enroll devices via MDM auto-enrollment. - Device6 will be enrolled via Windows Autopilot and Intune, so enrollment is allowed only for users in GroupA. - Based on the group memberships in the scenario, User4 and User1 are in GroupA, while User2 and User3 are not. Therefore only User4 and User1 can enroll Device6.
  • Quick tip for the exam:
- Remember: MDM user scope determines who can auto-enroll devices; MAM scope controls app protection enrollment. When a new Autopilot device is enrolled, the signing-in user must be in the MDM scope.

A
AI Tutor Explanation
4/29/2026 5:17:10 AM

Why this is correct

  • Correct answer: C. Extract the hardware ID information of each computer to a CSV file and upload the file from the Microsoft Intune admin center.

  • Why this is correct:
- Windows Autopilot requires devices to be registered by their hardware IDs (hash) before Autopilot can deploy Windows 10 Enterprise. - Collect the hardware IDs from the new Phoenix machines, save them in a CSV, and upload that CSV in the Intune/Windows Autopilot area. This maps each device to an Autopilot deployment profile. - After registration, you can assign Autopilot profiles (Windows 10 Enterprise, etc.). Other options (serial number CSV, generalizing, or Mobility settings) are not the initial Autopilot registration steps.

A
AI Tutor Explanation
4/25/2026 1:53:46 PM

Question 7:

  • Correct answer: B — A risk score is computed based on the number of remediations needed compared to the industry peer average.

Explanation:
  • Risk360 uses a remediation-based score. It benchmarks how many actions are required to fix issues against peers, giving a relative risk posture.
  • Why not the others:
- A: Not just total risk events by location. - C: Time to mitigate isn’t the primary scoring method. - D: Not a four-stage breach scoring approach.
Note: The page text shows a mismatch (it lists D as the answer), but the study guide describes the remediation-based scoring (B) as the correct concept.

A
AI Tutor Explanation
4/25/2026 1:42:20 PM

Question 104:

  • Correct answer: D) Multi-Terabyte (TB) Range

  • Brief explanation:
- clustering keys organize data into micro-partitions to improve pruning when queries filter on those columns. - The performance benefit is most significant for very large tables; for small tables the overhead of maintaining clustering outweighs gains. - Therefore, as a best practice, define clustering keys on tables at the TB scale.

C
Community Helper
4/25/2026 2:03:10 AM

Q23: Fabric Admin is correct. Because Domain admin cannot create domains. Only Fabric Admin can among the given options. Q51: Wrapping @pipeline.parameter.param1 inside {} will return a string. But question requires the expression to return Int, so correct answer should be @pipeline.parameter.param1 (no {})

A
AI Tutor Explanation
4/23/2026 3:07:03 PM

Question 62:

  • Correct answer: D (per the page)

  • Note: The explanation text on the page describes option B (use ZDX score and Analyze Score to trigger the Y Engine analysis), indicating a mismatch between the stated answer and the rationale.

  • Key concept: For fast root-cause analysis, leverage telemetry and auto-correlated insights:
- Use the user’s ZDX score for AWS and run Analyze Score to activate the Y Engine, which correlates metrics across network, client, and application to pinpoint the issue quickly.
  • Why the other options are less effective:
- A: Only checks for outages; doesn’t provide actionable root-cause analysis. - C: Deep Trace helps visibility but is manual and time-consuming. - D: Packet capture is invasive and slow; not the quickest path to root cause.

A
AI Tutor Explanation
4/23/2026 12:26:21 PM

Question 32:

  • Answer: A (2.4GHz)

  • Why: Lower-frequency signals have longer wavelengths and experience less attenuation when passing through walls and obstacles. Higher frequencies (5GHz, 6GHz) are more easily blocked by walls. NFC operates over very short distances and is not meant to penetrate walls. So 2.4 GHz best penetrates physical objects like walls.

A
AI Tutor Explanation
4/21/2026 8:48:36 AM

Question 3:

  • False is the correct answer (Option B).

Why:
  • In Snowflake, a database is a metadata object that exists within a single Snowflake account. Accounts are isolated—there isn’t one database that lives in multiple accounts.
  • You can access data across accounts via data sharing or database replication, but these create separate database objects in the other accounts (e.g., a database in the consumer account created from a share), not a single shared database across accounts.

So a single database cannot exist in more than one Snowflake account.

A
Anonymous User
4/16/2026 10:54:18 AM

Question 1:

  • Correct answer: Edate = sys.argv[1]
  • Why this is correct:
- When a Databricks Job passes parameters to a notebook, those parameters are supplied to the notebook's Python process as command-line arguments. The first argument after the script name is sys.argv[1], so date = sys.argv[1] captures the passed date value directly.
  • How it compares to other options:
- date = spark.conf.get("date") reads from Spark config, not from job parameters. - input() waits for user input at runtime, which isn’t how job parameters are provided. - date = dbutils.notebooks.getParam("date") would work if the notebook were invoked via dbutils.notebook.run with parameters, not

A
Anonymous User
4/15/2026 4:42:07 AM

Question 528:

  • Correct answer: NSG flow logs for NSG1 (Option B)

  • Why:
- Traffic Analytics uses NSG flow logs to analyze traffic patterns. You must have NSG flow logs enabled for the NSGs you want to monitor. - An Azure Log Analytics workspace is also required to store and query the traffic data. - Network Watcher must be available in the subscription for traffic analytics to function.
  • What to configure (brief steps):
- Ensure Network Watcher is enabled in the East US region (for the subscription/region). - Enable NSG flow logs on NSG1. - Ensure a Log Analytics workspace exists and is accessible (read/write) so Traffic Analytics can store and query logs.
  • Why other options aren’t correct:
- “Diagnostic settings for VM1” or “Diagnostic settings for NSG1” alone don’t guarantee flow logs are captured and sent to Log Analytics, which Traffic Analytics relies on. - “Insights for VM1” is not how Traffic Analytics collects traffic data.

A
Anonymous User
4/15/2026 2:43:53 AM

Question 23:
The correct answer is Domain admin (option B), not Fabric admin.

  • Domain admin provides domain-level management: create domains/subdomains and assign workspaces within those domains, which matches the tasks while following least privilege.
  • Fabric admin is global-level access and is more privileges than needed for this scenario (it would grant broader control across the Fabric environment).

A
Anonymous User
4/14/2026 12:31:34 PM

Question 2:
For question 2, the key concept is the Longest Prefix Match. Routers pick the route whose subnet mask is the most specific (largest prefix length) that still matches the destination IP.
From the options:

  • A) 10.10.10.0/28 ? 10.10.10.0–10.10.10.15
  • B) 10.10.13.0/25 ? 10.10.13.0–10.10.13.127
  • C) 10.10.13.144/28 ? 10.10.13.144–10.10.13.159
  • D) 10.10.13.208/29 ? 10.10.13.208–10.10.13.215

The destination Host A’s IP must fall within 10.10.13.208–10.10.13.215 for the /29 to be the best match. Since /29 is the longest prefix among the matching options, Router1 will use 10.10.13.208/29.
Thus, the correct answer is D.

S
srameh
4/14/2026 10:09:29 AM

Question 3:

  • Correct answer: Phase 4, Post Accreditation

  • Explanation:
- In DITSCAP, the four phases are: - Phase 1: Definition (concept and requirements) - Phase 2: Verification (design and testing) - Phase 3: Validation (fielding and evaluation) - Phase 4: Post Accreditation (ongoing operations and lifecycle management) - The description—continuing operation of an accredited IT system and addressing changing threats throughout its life cycle—fits the Post Accreditation phase, which covers operations, maintenance, monitoring, and reauthorization as threats and environment evolve.

O
onibokun10
4/13/2026 7:50:14 PM

Question 129:
Correct answer: CNAME

  • A CNAME record creates an alias for a domain, so newapplication.comptia.org will resolve to whatever IP address www.comptia.org resolves to. This ensures both names point to the same resource without duplicating the IP.
  • Why not the others:
- SOA defines authoritative information for a zone. - MX specifies mail exchange servers. - NS designates name servers for a zone.
  • Notes: The alias name (newapplication.comptia.org) should not have other records if you use a CNAME for it, and CNAMEs aren’t used for the zone apex (root) domain. This scenario uses a subdomain, so a CNAME is appropriate.

A
Anonymous User
4/13/2026 6:29:58 PM

Question 1:

  • Correct answer: C

  • Why this is best:
- Uses OS Login with IAM, so SSH access is granted via Google accounts rather than distributing per-user SSH keys. - Granting the compute.osAdminLogin role to a Google group gives admin access to all team members in a centralized, auditable way. - Access is auditable: Cloud Audit Logs show who accessed which VM, satisfying the security requirement to determine who accessed a given instance.
  • How it works:
- Enable OS Login on the project/instances (enable-oslogin metadata). - Add the team’s

A
Anonymous User
4/13/2026 1:00:51 PM

Question 2:

  • Answer: D. Azure Advisor

  • Why: To view security-related recommendations for resources in the Compute and Apps area (including App Service Web Apps and Functions), you use Azure Advisor. Advisor surfaces personalized best-practice recommendations across resources, including security, and shows which resources are affected and the severity.

  • Why not the others:
- Azure Log Analytics is for ad-hoc querying of telemetry, not for viewing security recommendations. - Azure Event Hubs is for streaming telemetry data, not for security recommendations.
  • Quick tip: In the portal, navigate to Azure Advisor and check the Security recommendations for App Services to see actionable items and affe

D
Don
4/11/2026 5:36:42 AM

Recommend using AI for Solutions rather the Answer(s) submitted here

M
Mogae Malapela
4/8/2026 6:37:56 AM

This is very interesting

A
Anon
4/6/2026 5:22:54 PM

Are these the same questions you have to pay for in ExamTopics?

L
LRK
3/22/2026 2:38:08 PM

For Question 7 - while the answer description indicates the correct answer, the option no. mentioned is incorrect. Nice and Comprehensive. Thankyou

R
Rian
3/19/2026 9:12:10 AM

This is very good and accurate. Explanation is very helpful even thou some are not 100% right but good enough to pass.

G
Gerrard
3/18/2026 6:58:37 AM

The DP-900 exam can be tricky if you aren't familiar with Microsoft’s specific cloud terminology. I used the practice questions from free-braindumps.com and found them incredibly helpful. The site breaks down core data concepts and Azure services in a way that actually mirrors the real test. As a resutl I passed my exam.

V
Vineet Kumar
3/6/2026 5:26:16 AM

interesting

J
Joe
1/20/2026 8:25:24 AM

Passed this exam 2 days ago. These questions are in the exam. You are safe to use them.

N
NJ
12/24/2025 10:39:07 AM

Helpful to test your preparedness before giving exam

A
Ashwini
12/17/2025 8:24:45 AM

Really helped

J
Jagadesh
12/16/2025 9:57:10 AM

Good explanation

S
shobha
11/29/2025 2:19:59 AM

very helpful

P
Pandithurai
11/12/2025 12:16:21 PM

Question 1, Ans is - Developer,Standard,Professional Direct and Premier

E
Einstein
11/8/2025 4:13:37 AM

Passed this exam in first appointment. Great resource and valid exam dump.

AI Tutor 👋 I’m here to help!