What is a potential negative consequence of using a high wall filter?
Answer(s): A
A high wall filter is used in Doppler ultrasound to eliminate low-frequency signals that may be attributed to vessel wall motion or other low-velocity flows. However, if the wall filter is set too high, it can inadvertently eliminate desired low-frequency Doppler signals that represent real blood flow, particularly in smaller vessels or those with slower flow velocities. This results in a loss of valuable diagnostic information.
ARDMS Sonography Principles and Instrumentation (SPI) Review, Doppler Ultrasound section.
During 3-D volume acquisition, the quality of the images is most dependent upon which factor?
During 3-D volume acquisition in ultrasound, the quality of the images is most dependent on the number of slices acquired. This is because the more slices (or planes) that are captured, the more detailed and accurate the reconstruction of the 3-D volume will be. This allows for better spatial resolution and more precise visualization of anatomical structures. Other factors, such as power output, rendering methods, and speed of post-processing, also affect image quality but are secondary to the number of slices in terms of fundamental image acquisition quality.
ARDMS Sonography Principles and Instrumentation (SPI) Review, 3-D Ultrasound Imaging section.
What occurs when the pulse repetition frequency is less than twice the Doppler shift frequency?
Answer(s): C
Aliasing occurs in Doppler ultrasound when the pulse repetition frequency (PRF) is less than twice the Doppler shift frequency (Nyquist limit). When this condition is met, the Doppler signals are not sampled frequently enough to accurately measure the frequency shifts, resulting in the misrepresentation of the flow velocities. This causes the aliasing artifact, where high-velocity flows are displayed incorrectly as wrapping around the baseline, leading to potential diagnostic errors.
ARDMS Sonography Principles and Instrumentation (SPI) Review, Doppler Artifacts section.
A Doppler shift is 10,000 Hz at an angle of flow of 60 degrees. What is the Doppler shift at 0 degrees?
depends on the angle between the ultrasound beam and the direction of blood flow. The Doppler equation includes a cosine function of the angle of insonation (). At 60 degrees, the cosine is 0.5, and at 0 degrees (parallel to the flow), the cosine is 1. Thus, if the Doppler shift is 10,000 Hz at 60 degrees, it would double to 20,000 Hz at 0 degrees because the cosine of 0 degrees is 1 (cos(0°) = 1) and the cosine of 60 degrees is 0.5 (cos(60°) = 0.5). The formula is: Doppler shift at 0 degrees = Doppler shift at 60 degrees / cos(60 degrees) = 10,000 Hz / 0.5 = 20,000 Hz.
ARDMS Sonography Principles and Instrumentation (SPI) Review, Doppler Shift and Angle of Insonation section.
Which unfocused transducer will have the greatest divergence?
Transducer beam divergence is influenced by the aperture size and frequency. A smaller aperture and lower frequency result in greater beam divergence. Among the given options, the transducer with a 4 mm aperture and 4 MHz frequency will have the greatest divergence. This is because the smaller aperture size contributes to a wider beam spread, and the lower frequency also increases the divergence compared to higher frequencies.
ARDMS Sonography Principles and Instrumentation guidelinesKremkau, F. W. (2015). Diagnostic Ultrasound: Principles and Instruments. Elsevier.
What happens to the amount of attenuation if the path length is doubled?
Answer(s): B
Attenuation in ultrasound is directly proportional to the path length. If the path length is doubled, the amount of attenuation is also doubled. Attenuation refers to the reduction in the amplitude and intensity of the ultrasound wave as it travels through tissue, primarily due to absorption, reflection, and scattering. The relationship is linear, so doubling the distance the sound wave travels will result in twice the amount of attenuation.
Which type of resolution will be improved by decreasing the depth of field?
Lateral resolution refers to the ability to distinguish two structures that are side by side. It is dependent on the width of the ultrasound beam. By decreasing the depth of field, the beam width is reduced at any given point along the depth, which improves the lateral resolution. This is because a narrower beam can better distinguish between objects that are close together laterally.
ARDMS Sonography Principles and Instrumentation guidelinesKremkau, F. W. (2015). Diagnostic Ultrasound: Principles and Instruments.
What improves the temporal resolution of color flow imaging?
Temporal resolution refers to the ability of the ultrasound system to distinguish events occurring closely in time. In color flow imaging, temporal resolution is affected by the frame rate, which can be increased by decreasing the width of the color field of view. This is because a narrower color field requires fewer scan lines to be processed, allowing for more frames to be captured per second.
ARDMS Sonography Principles and Instrumentation guidelinesEdelman, S. K. (2017). Understanding Ultrasound Physics.
Share your comments for ARDMS SPI exam with other users:
hi team just want to know if there is any update version of the exam 350-401
helpful on 2017 scrum guide
planning to attempt for the exam.
pleaseee upload
thanks ly so i have information cia
hello team, i need sap qm dumps for practice
it’s good but not senatios based
q.119 - the correct answer is b - they are not captured in an update set as theyre data.
good matter
please upload c_sacp_2308
please upload the dump. thanks very much !!
good questions
hi, could you please update the latest dump version
this question is keep repeat : you are developing a sales application that will contain several azure cloud services and handle different components of a transaction. different cloud services will process customer orders, billing, payment, inventory, and shipping. you need to recommend a solution to enable the cloud services to asynchronously communicate transaction information by using xml messages. what should you include in the recommendation?
great questions
its realy good
oracle 1z0-1059-22 dumps
please share me the pdf..
q50: which two functions can be used by an end user when pivoting an interactive report? the correct answer is a, c because we do not have rank in the function pivoting you can check in the apex app
best to practice
so far it is good
please provide me the dump
i failed the cisa exam today. but i have found all the questions that were on the exam to be on this site.
in question 272 the right answer states that an autonomous acces point is "configured and managed by the wlc" but this is not what i have learned in my ccna course. is this a mistake? i understand that lightweight aps are managed by wlc while autonomous work as standalones on the wlan.
it was helpful
good question
really nice
please i need dumps for isc2 cybersecuity
ans is coldline i think
very helpful
can you please provide dumps so that it helps me more
thank you for providing me with the updated question and answers. this version has all the questions from the exam. i just saw them in my exam this morning. i passed my exam today.
how i can see exam questions?
can you please upload please?
Keeping this site free takes real effort. We constantly battle automated scraping and unauthorized content copying. A quick account helps us protect the community and keep the site free.
To continue studying for your SPI, please sign in or create a free account.