Compared with HDDs, SSDs have high I/O performance and low latency.
Answer(s): A
According to Huawei's technical documentation on storage media, Solid State Drives (SSDs) fundamentally differ from Hard Disk Drives (HDDs) in their physical construction and data access methods. HDDs rely on mechanical components, including rotating platters and moving read/write heads. This mechanical nature introduces "rotational latency" and "seek time," which inherently limit the number of Input/Output Operations Per Second (IOPS).In contrast, Huawei's OceanStor SSDs utilize flash memory chips (NAND Flash) and a high- performance controller. Because there are no moving parts, the "seek time" is eliminated, allowing for near-instantaneous data access. This results in significantly higher random IOPS and much lower latency (often measured in microseconds rather than milliseconds). Furthermore, Huawei's FlashLink® technology further optimizes the collaboration between the storage controller and the SSDs, ensuring that even as the drive fills up, the performance remains consistent and the latency remains low. Therefore, in any performance-oriented storage environment, SSDs are the preferred choice over traditional HDDs.
Which RAID level cannot provide data redundancy protection?
Answer(s): D
In the Huawei OceanStor RAID 2.0+ architecture, Redundant Array of Independent Disks (RAID) levels are used to balance performance, capacity, and reliability. RAID 0, also known as "striping," distributes data blocks across multiple physical disks to maximize I/O performance. By allowing multiple disks to be read or written simultaneously, it provides the highest throughput and capacity utilization (100%).However, the defining characteristic of RAID 0 is the complete lack of redundancy. Unlike RAID 1(Mirroring), RAID 5 (Parity), or RAID 6 (Dual Parity), RAID 0 does not store redundant information or parity bits. Huawei documentation explicitly states that if any single physical disk in a RAID 0 group fails, the entire RAID group becomes inaccessible, and all data within that group is lost. Therefore, RAID 0 is strictly recommended only for temporary data or scenarios where data loss is acceptable and maximum performance is the sole priority. For enterprise production environments, Huawei recommends RAID 5, RAID 6, or RAID-TP.
What are the main application scenarios for SAN storage? (Select all that apply)
Answer(s): B,C
Storage Area Network (SAN) storage is designed to provide block-level data access to servers, appearing to the operating system as a locally attached hard drive. Huawei OceanStor SAN solutions (both FC-SAN and IP-SAN) are optimized for high-performance, low-latency applications.Databases (Option C), such as Oracle, SQL Server, and DB2, are primary use cases for SAN storage because they require high IOPS and low latency for transactional processing. The block-level access allows the database management system to have granular control over data placement and caching. VMware virtualization (Option B) is another core scenario. SANs provide the shared storage necessary for advanced features like VMotion, High Availability (HA), and Distributed Resource Scheduler (DRS). In these environments, multiple ESXi hosts connect to a centralized SAN to access VMFS (Virtual Machine File System) volumes. While Option A (Big Data) and Option D (File Sharing) often use Distributed Storage (OceanStor Pacific) or NAS, the high-concurrency, structured nature ofDatabases and Virtualization makes them the definitive scenarios for SAN.
RAID 0 is actually a mirroring technology.
Answer(s): B
This statement is false because RAID 0 and Mirroring (RAID 1) are fundamentally different concepts in Huawei storage technology. As defined in the Huawei technical manual, RAID 0 is "Striping." It breaks data into chunks and spreads them across multiple disks to increase performance. It has no redundancy."Mirroring" is the terminology specifically used for RAID 1. In a RAID 1 configuration, the system writes the exact same data to two separate physical disks simultaneously. This creates a 100% redundant copy (a mirror). If one disk fails, the other continues to provide data, ensuring zero downtime and no data loss. Huawei's RAID 2.0+ virtualization technology can implement striping and mirroring across different "chunks" or "extents" within a storage pool, but it maintains the technical distinction: RAID 0 is for performance through striping, while mirroring is for reliability through duplication. Therefore, characterizing RAID 0 as a mirroring technology is a technical inaccuracy.
Which statements are correct about NVMe over Fabrics (NVMe-oF) (RoCE v2)? (Select all that apply)
NVMe over Fabrics (NVMe-oF) using the RoCE v2 (RDMA over Converged Ethernet) protocol is a high-speed communication technology supported by Huawei OceanStor Dorado systems. Option B is correct because RoCE v2 utilizes RDMA, which allows data to be transferred directly from the memory of one computer to another without involving the CPU of either system. This significantly reduces latency and CPU overhead compared to traditional iSCSI.Option C is correct because RoCE v2 requires a "Lossless Ethernet" environment to function correctly. Traditional Ethernet (Option A) is a "best-effort" delivery system that allows for packet drops during congestion; however, RDMA protocols are highly sensitive to packet loss. To support RoCE v2, the network must implement Data Center Bridging (DCB) features like Priority Flow Control (PFC) and Enhanced Transmission Selection (ETS) to ensure a zero-packet-loss environment. Regarding cost (Option D), RoCE v2 often leverages existing Ethernet infrastructure, making it generally more cost- effective than deploying a dedicated Fibre Channel (FC) fabric, which requires specialized HBAs and FC switches.
What are the topologies of a Fibre Channel (FC) network? (Select all that apply)
Answer(s): A,C,D
According to Huawei's storage networking guides, Fibre Channel (FC) supports three primary physical topologies to facilitate communication between servers (initiators) and storage arrays (targets).Point-to-point (Option C): This is the simplest topology where two nodes are directly connected. It provides dedicated bandwidth but lacks scalability.Arbitrated loop (FC-AL) (Option D): In this setup, devices are connected in a loop shared by all nodes. While more scalable than point-to-point, only one pair of nodes can communicate at a time, leading to performance bottlenecks as more devices are added.Fabric (FC-SW) (Option A): This is the most common enterprise topology, utilizing FC switches. It allows many-to-many communication, providing high scalability, redundancy, and independent bandwidth for each connection."Bus" (Option B) is a topology associated with older Ethernet or SCSI standards and is not a recognized topology in Fibre Channel networking. Huawei OceanStor Dorado and Hybrid systems primarily utilize the Fabric topology for large-scale data center deployments to ensure maximum availability and performance through redundant switch fabrics.
Thin provisioning allocates storage space on demand, improving resource utilization.
Huawei's SmartThin technology is a thin provisioning feature that allows storage administrators to allocate more logical capacity to servers than is physically available in the storage pool. Traditionally, "thick provisioning" reserves the entire capacity of a LUN the moment it is created, leading to significant "stranded" or wasted space if the application does not immediately use it.With SmartThin, the storage system only consumes physical blocks when data is actually written to the disk. This "on-demand" allocation ensures that physical resources are shared across multiple LUNs more efficiently. For example, a 10 TB LUN might be presented to a database, but if the database only contains 2 TB of data, only 2 TB of physical space is consumed. This significantly improves the Storage Resource Utilization Rate and reduces the Total Cost of Ownership (TCO) by delaying the need to purchase additional physical disks until the actual consumed capacity approaches the physical limits of the array.
What are the characteristics of DAS? (Select all that apply)
Answer(s): A,B,C
Direct-Attached Storage (DAS) is a traditional storage architecture where storage devices are connected directly to a host server. Huawei documentation defines the following key characteristics:Direct Connection (Option C): DAS connects to the server via internal or external interfaces such as SATA, SAS, or SCSI, rather than through a storage network.No Network Devices (Option A): Because it is a 1-to-1 connection, it does not require Fibre Channel switches or Ethernet switches to facilitate the link between the host and the storage. This makes it simple and cost-effective for small-scale deployments.Block Storage Services (Option B): Like a SAN, DAS provides block-level access. The server's operating system manages the file system (NTFS, EXT4, etc.) directly on the provided blocks.While a server attached to DAS can share its files over a network (becoming a file server), the DAS itself is not a "File Storage Service" (Option D). In Huawei's hierarchy, file services are the domain of NAS (Network Attached Storage), which provides shared access to files via protocols like CIFS/SMB or NFS.
Share your comments for Huawei H19-308_V4.0 exam with other users:
answer to this question "what administrative safeguards should be implemented to protect the collected data while in use by manasa and her product management team? " it should be (c) for the following reasons: this administrative safeguard involves controlling access to collected data by ensuring that only individuals who need the data for their job responsibilities have access to it. this helps minimize the risk of unauthorized access and potential misuse of sensitive information. while other options such as (a) documenting data flows and (b) conducting a privacy impact assessment (pia) are important steps in data protection, implementing a "need to know" access policy directly addresses the issue of protecting data while in use by limiting access to those who require it for legitimate purposes. (d) is not directly related to safeguarding data during use; it focuses on data transfers and location.
password lockout being the correct answer for question 37 does not make sense. it should be geofencing.
for question 4, the righr answer is :recover automatically from failures
question number 4s answer is 3, option c. i
very good questions
i am confused about the answers to the questions. are the answers correct?
very usefull
need certification.
great exam prep
i require dump
good morning, could you please upload this exam again,
hi can you please upload the dumps for sap contingent module. thanks
good questions
looking forward to the real exam
good ones for exam preparation
this is a good experience
hi everyone
waiting for the dump. please upload.
upload cks exam questions
awesome training material
where is dump
q. 289 - the correct answer should be b not d, since the question asks for the most secure way to provide access to a s3 bucket (a single one), and by principle of the least privilege you should not be giving access to all buckets.
please i need if possible h12-831,
good collection of questions and solution for pl500 certification
i would like to appear the exam.
i am very happy as i cleared my comptia a+ 220-1101 exam. i studied from as it has all exam dumps and mock tests available. i got 91% on the test.
need this dump
its really good to eventuate knowledge before appearing for the actual exam.
this is great
please i want the questions to pass the exam
i need to pass exam
great, i appreciate it.
please could you upload (isc)2 certified in cybersecurity (cc) exam questions
good questions, wrong answers