Fortinet FCSS - Network Security 7.6 Support Engineer FCSS_NST_SE-7.6 Dumps in PDF

Free Fortinet FCSS_NST_SE-7.6 Real Questions (page: 12)

Refer to the exhibit.



Which three pieces of information does the diagnose sys top command provide? (Choose three.)

  1. The miglogd daemon is running on CPU core ID 0.
  2. The diagnose sys top command has been running for 18 minutes.
  3. The miglogd daemon would be on top of the list, if the administrator pressed m on the keyboard.
  4. The cmdbsvr process is occupying 2.4% of the total user memory space.
  5. If the neweli daemon continues to be in the R state, it will need to be manually restarted.

Answer(s): A,C,D

Explanation:

https://community.fortinet.com/t5/FortiGate/Technical-Tip-Using-the-diagnose-sys-top-CLI- command/ta-p/190238



Refer to the exhibit, which shows the output o! the BGP database.



Which two statements are correct? (Choose two.)

  1. The advertised prefix of 10.20.30.0/24 was configured using the network command.
  2. The first four prefixes are being advertised using a legacy route advertisement.
  3. The advertised prefix of 10.20.30.0/24 is being advertised through the redistribution of another routing protocol.
  4. The output shows all prefixes advertised by all neighbors as well as the local router.

Answer(s): A,D

Explanation:

For Option A:
In Fortinet BGP (and standard BGP), when a prefix is displayed with an "i" (lowercase i) in the Path column, it represents an internal prefix that originated from the local router, typically configured via the BGP "network" command. In the exhibit, the prefix 10.20.30.0/24 is listed with a Path value of i, indicating it was injected into BGP by the local router using the network statement, not via redistribution from another routing protocol. The same logic applies to i as documented: "Origin code 'i' means the route was injected via the network command."

For Option D:
The get router info bgp network output is a summary table displaying both local and received BGP routes. It lists all known routes to the BGP process, whether received from peers or originated locally. The exhibit shows all BGP prefixes known to the local router, matching the official admin guide's description of this command's output.

Explanation for B and C:

The phrase "legacy route advertisement" is not formalized in BGP documentation or Fortinet's admin guide; the output uses standard BGP mechanics.

If a route was redistributed into BGP from another routing protocol, the Path field would display a "?" (question mark) for incomplete (redistributed) origin. Here the /24 route has "i" so it is NOT a redistribution.


Reference:

FortiOS Administration Guide: BGP Configuration and Route Table Interpretation

Official BGP Command

Show BGP Network, Path Codes, Route Origination Indicators



In which two slates is a given session categorized as ephemeral? (Choose two.)

  1. A UDP session with only one packet received
  2. A UOP session with packets sent and received
  3. A TCP session waiting for the SYN ACK
  4. A TCP session waiting for FIN ACK

Answer(s): A,C



Refer to the exhibit, which shows the output of get router info bgp summary.



Which two statements are true? (Choose two.)

  1. The local ForliGate has received one prefix from BGP neighbor 100.64.1.254.
  2. The TCP connection with BGP neighbor 100.64.2.254 was successful.
  3. The local FortiGate has received 18 packets from a BGP neighbor.
  4. The local FortiGate is still calculating the prefixes received from BGP neighbor 100.64.2.264

Answer(s): A,C

Explanation:

The get router info bgp summary output lists BGP neighbor status:

Prefix Reception: The "State/PfxRcd" column shows the number of prefixes received from the neighbor--neighbor 100.64.1.254 has "1", confirming option A.

Received Message Count: Under "MsgRcvd", 18 packets have been received from neighbor 100.64.1.254. This matches option C.

The second neighbor 100.64.2.254 is in "Active" state and has received/sent 0 packets, indicating that its TCP connection is NOT established, disproving option B.

There is no indication anywhere that the router is "still calculating" prefixes; "Active" just means no session is established, so option D is incorrect.


Reference:

FortiOS BGP Command
BGP Neighbor States, PfxRcd, and Counters



Which exchange lakes care of DoS protection in IKEv2?

  1. Create_CHILD_SA
  2. IKE_Auth
  3. IKE_Req_INIT
  4. IKE_SA_NIT

Answer(s): C

Explanation:

The IKE_SA_INIT exchange in IKEv2 is responsible for DoS protection measures. During IKE_SA_INIT, before authentication and further exchange, the responder can use cookie challenges (per RFC 7296 and Fortinet VPN documentation). If a DoS attack is suspected (many requests from the same source), the responder replies with a cookie. Only after the initiator returns the correct cookie does the exchange proceed, protecting the responder from state exhaustion and certain forms of DoS traffic at the handshake stage.


Reference:

FortiOS VPN Manual: IKEv2 Exchange Process and DoS Protections

IKEv2 RFC 7296: Description of IKE_SA_INIT and DoS Cookie Mechanism



Refer to the exhibit, which shows a partial output of the fssod daemon real-time debug command.



What two conclusions can you draw from the output? (Choose two.)

  1. The workstation with IP 10.124.2.90 will be polled frequently using TCP port 445 to see if the user is still logged on.
  2. The logon event can be seen on the collector agent installed on Windows.
  3. FSSO is using DC agent mode to detect logon events.
  4. FSSO is using agentless polling mode to detect logon events.

Answer(s): A,D

Explanation:

https://community.fortinet.com/t5/FortiGate/Troubleshooting-Tip-How-to-troubleshoot-FSSO- agentless-polling/ta-p/214349

From the snippet we can see that FortiGate (via the fssod daemon) is directly detecting the user logon rather than relying on a separate "collector" or "DC agent." This indicates agentless polling-- FortiGate polls the DC's event logs over TCP 445 to discover logons. So: - FSSO is using agentless polling mode to detect logon events - In agentless mode, FortiGate will periodically poll the same IP (the DC) on port 445 to see if the user is still logged on



An administrator wants to capture encrypted phase 2 traffic between two FotiGate devices using the built-in sniffer.

If the administrator knows that there Is no NAT device located between both FortiGate devices, which command should the administrator run?

  1. diagnose sniffer packet any 'udp port 500'
  2. diagnose sniffer packet any 'lp proto 50'
  3. diagnose sniffer packet any 'udp port 4500'
  4. diagnose sniffer packet any 'ah'

Answer(s): B

Explanation:

To capture encrypted IPsec phase 2 (ESP) traffic between two FortiGate devices, the correct protocol filter to use is ip proto 50. According to the Fortinet official sniffing and debugging documentation, ESP (Encapsulating Security Payload) is used for encrypted phase 2 payload transfer and always uses IP protocol number 50. Running the command diagnose sniffer packet any 'ip proto 50' captures only ESP packets, which represent the encrypted traffic--whether originating or transiting the device.

If there is no NAT device between FortiGates, ESP is not encapsulated in UDP (thus not on UDP port 4500; if NAT-T were required, packets would be UDP-encapsulated, but the scenario explicitly says

NAT is not in use). UDP port 500 is for IKE control (negotiation) traffic, and AH (Authentication Header, ip proto 51) is not used for encryption in standard IPsec phase 2 with ESP.

This matches the official CLI reference from Fortinet for VPN and traffic analysis.

**


Reference:

FortiOS CLI
diagnose sniffer packet, ESP, IP Protocol Numbers

FortiGate VPN Administration Guide: Traffic Capture and Analysis of IPsec Traffic



Refer to the exhibits.



An administrator Is expecting to receive advertised route 8.8.8.8/32 from FGT-A. On FGT-B, they confirm that the route is being advertised and received, however, the route is not being injected into the routing table.
What is the most likely cause of this issue?

  1. A batter route to the 8.8.8.8/32 network exists in the routing table.
  2. FGT-B is configured with a prefix list denying the 8.8.8.8/32 network to be injected into the routing table.
  3. The administrator has misconfigured redistribution of routes on FGT-A.
  4. FGT-8 is configured with a distribution list denying the 8.8.8.8/32 network to be injected into the routing table.

Answer(s): B

Explanation:

The 8.8.8.8/32 route is visible in the OSPF database on FGT-B but not installed into the routing table--the most likely explanation is that FGT-B is filtering it from being installed.



Share your comments for Fortinet FCSS_NST_SE-7.6 exam with other users:

A
Anonymous User
4/13/2026 6:29:58 PM

Question 1:

  • Correct answer: C

  • Why this is best:
- Uses OS Login with IAM, so SSH access is granted via Google accounts rather than distributing per-user SSH keys. - Granting the compute.osAdminLogin role to a Google group gives admin access to all team members in a centralized, auditable way. - Access is auditable: Cloud Audit Logs show who accessed which VM, satisfying the security requirement to determine who accessed a given instance.
  • How it works:
- Enable OS Login on the project/instances (enable-oslogin metadata). - Add the team’s

A
Anonymous User
4/13/2026 1:00:51 PM

Question 2:

  • Answer: D. Azure Advisor

  • Why: To view security-related recommendations for resources in the Compute and Apps area (including App Service Web Apps and Functions), you use Azure Advisor. Advisor surfaces personalized best-practice recommendations across resources, including security, and shows which resources are affected and the severity.

  • Why not the others:
- Azure Log Analytics is for ad-hoc querying of telemetry, not for viewing security recommendations. - Azure Event Hubs is for streaming telemetry data, not for security recommendations.
  • Quick tip: In the portal, navigate to Azure Advisor and check the Security recommendations for App Services to see actionable items and affe

D
Don
4/11/2026 5:36:42 AM

Recommend using AI for Solutions rather the Answer(s) submitted here

M
Mogae Malapela
4/8/2026 6:37:56 AM

This is very interesting

A
Anon
4/6/2026 5:22:54 PM

Are these the same questions you have to pay for in ExamTopics?

L
LRK
3/22/2026 2:38:08 PM

For Question 7 - while the answer description indicates the correct answer, the option no. mentioned is incorrect. Nice and Comprehensive. Thankyou

R
Rian
3/19/2026 9:12:10 AM

This is very good and accurate. Explanation is very helpful even thou some are not 100% right but good enough to pass.

G
Gerrard
3/18/2026 6:58:37 AM

The DP-900 exam can be tricky if you aren't familiar with Microsoft’s specific cloud terminology. I used the practice questions from free-braindumps.com and found them incredibly helpful. The site breaks down core data concepts and Azure services in a way that actually mirrors the real test. As a resutl I passed my exam.

V
Vineet Kumar
3/6/2026 5:26:16 AM

interesting

J
Joe
1/20/2026 8:25:24 AM

Passed this exam 2 days ago. These questions are in the exam. You are safe to use them.

N
NJ
12/24/2025 10:39:07 AM

Helpful to test your preparedness before giving exam

A
Ashwini
12/17/2025 8:24:45 AM

Really helped

J
Jagadesh
12/16/2025 9:57:10 AM

Good explanation

S
shobha
11/29/2025 2:19:59 AM

very helpful

P
Pandithurai
11/12/2025 12:16:21 PM

Question 1, Ans is - Developer,Standard,Professional Direct and Premier

E
Einstein
11/8/2025 4:13:37 AM

Passed this exam in first appointment. Great resource and valid exam dump.

D
David
10/31/2025 4:06:16 PM

Today I wrote this exam and passed, i totally relay on this practice exam. The questions were very tough, these questions are valid and I encounter the same.

T
Thor
10/21/2025 5:16:29 AM

Anyone used this dump recently?

V
Vladimir
9/25/2025 9:11:14 AM

173 question is A not D

K
khaos
9/21/2025 7:07:26 AM

nice questions

K
Katiso Lehasa
9/15/2025 11:21:52 PM

Thanks for the practice questions they helped me a lot.

E
Einstein
9/2/2025 7:42:00 PM

Passed this exam today. All questions are valid and this is not something you can find in ChatGPT.

V
vito
8/22/2025 4:16:51 AM

i need to pass exam for VMware 2V0-11.25

M
Matt
7/31/2025 11:44:40 PM

Great questions.

O
OLERATO
7/1/2025 5:44:14 AM

great dumps to practice for the exam

A
Adekunle willaims
6/9/2025 7:37:29 AM

How reliable and relevant are these questions?? also i can see the last update here was January and definitely new questions would have emerged.

A
Alex
5/24/2025 12:54:15 AM

Can I trust to this source?

S
SPriyak
3/17/2025 11:08:37 AM

can you please provide the CBDA latest test preparation

C
Chandra
11/28/2024 7:17:38 AM

This is the best and only way of passing this exam as it is extremely hard. Good questions and valid dump.

S
Sunak
1/25/2025 9:17:57 AM

Can I use this dumps when I am taking the exam? I mean does somebody look what tabs or windows I have opened ?

F
Frank
2/15/2024 11:36:57 AM

Finally got a change to write this exam and pass it! Valid and accurate!

A
Anonymous User
2/2/2024 6:42:12 PM

Upload this exam please!

N
Nicholas
2/2/2024 6:17:08 PM

Thank you for providing these questions. It helped me a lot with passing my exam.

T
Timi
8/19/2023 5:30:00 PM

my first attempt

AI Tutor 👋 I’m here to help!