Cisco 300-710 Dumps PDF Free Download - Page: 9

QUESTION: 41 Exam Topic: 2, Configuration

Which two types of objects are reusable and supported by Cisco FMC? (Choose two.)

dynamic key mapping objects that help link HTTP and HTTPS GET requests to Layer 7 application protocols.
reputation-based objects that represent Security Intelligence feeds and lists, application filters based on category and reputation, and file lists
network-based objects that represent IP address and networks, port/protocols pairs, VLAN tags, security zones, and origin/destination country
network-based objects that represent FQDN mappings and networks, port/protocol pairs, VXLAN tags, security zones and origin/destination country
reputation-based objects, such as URL categories

Answer(s): B,C

Reference:

https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config- guide-v62/reusable_objects.html#ID-2243-00000414

Reveal Solution Next Question

QUESTION: 42 Exam Topic: 2, Configuration

A network administrator notices that remote access VPN users are not reachable from inside the network. It is determined that routing is configured correctly, however return traffic is entering the firewall but not leaving it.
What is the reason for this issue?

A manual NAT exemption rule does not exist at the top of the NAT table.
An external NAT IP address is not configured.
An external NAT IP address is configured to match the wrong interface.
An object NAT exemption rule does not exist at the top of the NAT table.

Answer(s): A

Reference:

https://www.cisco.com/c/en/us/support/docs/security/firepower-management-center/212702- configure-and-verify-nat-on-ftd.html

Reveal Solution Next Question

QUESTION: 43 Exam Topic: 2, Configuration

An administrator is creating interface objects to better segment their network but is having trouble adding interfaces to the objects.
What is the reason for this failure?

The interfaces are being used for NAT for multiple networks.
The administrator is adding interfaces of multiple types.
The administrator is adding an interface that is in multiple zones.
The interfaces belong to multiple interface groups.

Answer(s): D

Reference:

https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config- guide-v62/reusable_objects.html#ID-2243-000009b4
"All interfaces in an interface object must be of the same type: all inline, passive, switched, routed, or ASA FirePOWER. After you create an interface object, you cannot change the type of interfaces it contains."

Reveal Solution Next Question

QUESTION: 44 Exam Topic: 2, Configuration

An organization is using a Cisco FTD and Cisco ISE to perform identity-based access controls. A network administrator is analyzing the Cisco FTD events and notices that unknown user traffic is being allowed through the firewall. How should this be addressed to block the traffic while allowing legitimate user traffic?

Modify the Cisco ISE authorization policy to deny this access to the user.
Modify Cisco ISE to send only legitimate usernames to the Cisco FTD.
Add the unknown user in the Access Control Policy in Cisco FTD.
Add the unknown user in the Malware & File Policy in Cisco FT

Answer(s): C

Reference:

https://www.cisco.com/c/en/us/td/docs/security/firepower/640/fdm/fptd-fdm-config- guide-640/fptd-fdm-identity.html#concept_655B055575E04CA49B10186DEBDA301A

Reveal Solution Next Question

QUESTION: 45 Exam Topic: 2, Configuration

A company is in the process of deploying intrusion prevention with Cisco FTDs managed by a Cisco FMC. An engineer must configure policies to detect potential intrusions but not block the suspicious traffic.
Which action accomplishes this task?

Configure IDS mode when creating or editing a policy rule under the Cisco FMC Intrusion tab in Access Policies section by unchecking the "Drop when inline" option.
Configure IPS mode when creating or editing a policy rule under the Cisco FMC Intrusion tab in Access Policies section by checking the "Drop when inline" option.
Configure IPS mode when creating or editing a policy rule under the Cisco FMC Intrusion tab in Access Policies section by unchecking the "Drop when inline" option.
Configure IDS mode when creating or editing a policy rule under the Cisco FMC Intrusion tab in Access Policies section by checking the "Drop when inline" option.

Answer(s): A

Reveal Solution Next Question

Cisco Securing Networks with Firepower (300-710 SNCF) 300-710 Dumps in PDF

Free Cisco 300-710 Real Questions (page: 9)

QUESTION: 41 Exam Topic: 2, Configuration

Reference:

QUESTION: 42 Exam Topic: 2, Configuration

Reference:

QUESTION: 43 Exam Topic: 2, Configuration

Reference:

QUESTION: 44 Exam Topic: 2, Configuration

Reference:

QUESTION: 45 Exam Topic: 2, Configuration